參數資料
型號： M37902FCCHP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100
文件頁數： 49/143頁
文件大?。?/td> 1148K
代理商： M37902FCCHP
Corrections and Supplementary Explanation for M37902FxC Datasheet (REV.B) NO.10
Page
Error
Correction
(10/11)
Page 108,
Fig. 115
The CPU reprogramming mode select bit is set to “1”.
(Writing of “0”
→ Writing of “1”)
Writing of “1” to the CPU reprogramming mode select
bit.
(Writing of “0”
→ Writing of “1”)
5
Page 108,
Software
Commands
5
(D8–D15) is ignored.
(Lines 6, 7)
(D8–D15) is ignored. (Except for the write data at
the 2nd cycle of a page programming command.)
(Lines 6, 7)
Page 109,
Page
programming
Command
5
(After line 20)
, the same way as bit 7 of the status register.
Reading out the
(Lines 4 to 7)
, the same wayas bit 7 of the status register.
Before execution of the next command, be sure to verify
that bit 7 of the status register (SR.7) or the RY/BY
status bit is set to “1” (READY). During the automatic
programming operation, writing of commands and
access to the flash memory must not be performed.
Reading out the
Page 109,
Block Erase
Command
5
(Lines 20 to 23)
, the same way as bit 7 of the status register.
Reading out the
(Lines 20 to 23)
, the same way as bit 7 of the status register.
Before execution of the next command, be sure to verify
that bit 7 of the status register (SR.7) or the RY/BY
status bit is set to “1” (READY). During the automatic
erase operation, writing of commands and access
to the flash memory must not be performed.
Reading out the
Page 111,
Erase All
Unlocked Block
Command
5
(Lines 9 to 11)
is also reported by a read of the status register.
When the lock bit
(Lines 9 to 11)
is also reported by a read of the status register.
During the automatic erase operation (when the RY/BY
status bit = “0” ), writing of commands and access to the
flash memory must not be performed.
When the lock bit
Page 108,
Page
programming
Command
5
(Lines 4 to 7)
mode is maintained.
(After line 20)
mode is maintained. In continuous programming,
if there is no programming error, page programming
commands can be executed with the read status register
mode kept.
(Titlle)
Page Program Command (4116)
(Titlle)
Page Programming Command (4116)
Page 111,
Data Protect
Function
(Block Lock)
5
(After line 20)
lock bit is terminated.
(After line 20)
lock bit is terminated.
To perform erase or programming, be sure to do one of
the following.
By executing the read lock bit status command, verify
that the lock of the target block is invalid.
Set the lock bit invalidity select bit to “1” to invalidate
the lock.
When the block erase or programming is performed with
the lock valid, the erase status bit (SR.5) and program-
ming status bit (SR.4) are set to “1” (terminated by error).
Page 114,
ABSOLUTE
MAXIMUM
RATINGS
5
300
Ratings
Symbol
Pd
Power disspation
Parameter
Unit
mW
400
Ratings
Symbol
Pd
Power disspation
Parameter
Unit
mW
Topr
Operating temperature
Topr
Operating ambient
temperature
相關PDF資料
PDF描述
M37902FGCHP 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100
M37906F8CSP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42
M37906F8CFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDSO42
M37906F8CSP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PDIP42
M37920S4CGP 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M37902FGCGP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37902FGCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37902FJCHP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37903S4CHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER
M37905F8CFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*