- 您現在的位置：買賣IC網 > PDF目錄16231 > KSZ8851SNL-BBE-EVAL (Micrel Inc)BOARD EVAL MAC/PHY FOR KSZ8851 PDF資料下載
參數資料
| 型號： | KSZ8851SNL-BBE-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 46/80頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL MAC/PHY FOR KSZ8851 |
| 軟件下載： | KSZ8851SNL Linux Driver Linus' GIT Repo View Driver |
| 設計資源： | Zippy2 Schematic BeagleBoard Zippy2 KSZ8851SNL-BBE-EVAL Bill of Materials |
| 特色產品： | Zippy 2 |
| 標準包裝： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851SNL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | SPI 接口，LinkMD 線纜診斷 |
| 已供物品： | 板，硬件 |
| 產品目錄頁面： | 1114 (CN2011-ZH PDF) |
| 其它名稱： | 576-3602 KSZ8851SNL-BBE-EVL ZIPPY2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Micrel, Inc.
KSZ8851SNL/SNLI
August 2009
50
M9999-083109-2.0
Bit
Default Value
R/W
Description
6
0x0
RW
RXME Receive Multicast Enable
When this bit is set, the RX module receives all the multicast frames (including broadcast
frames).
5
0x0
RW
RXUE Receive Unicast Enable
When this bit is set, the RX module receives unicast frames that match the 48-bit Station
MAC address of the module.
4
0x0
RW
RXAE Receive All Enable
When this bit is set, the KSZ8851SNL receives all incoming frames, regardless of the
frame’s destination address (see Address Filtering Scheme in Table 3 for detail).
3
0x0
RW
Reserved
2
0x0
RW
Reserved
1
0x0
RW
RXINVF Receive Inverse Filtering
When this bit is set, the KSZ8851SNL receives function with address check operation in
inverse filtering mode (see Address Filtering Scheme in Table 3 for detail).
0
0x0
RW
RXE Receive Enable
When this bit is set, the RX block is enabled and placed in a running state.
When this bit is cleared, the receive process is placed in the stopped state upon
completing reception of the current frame.
Receive Control Register 2 (0x76 – 0x77): RXCR2
This register holds control information programmed by the CPU to control the receive function.
Bit
Default Value
R/W
Description
15-8
-
RO
Reserved
7-5
0x0
WO
SRDBL SPI Receive Data Burst Length
These three bits are used to define for SPI receive data burst length during DMA
operation from the host CPU to access RXQ frame buffer.
000: 4 Bytes data burst
001: 8 Bytes data burst
010: 16 Bytes data burst
011: 32 Bytes data burst
100: Single frame data burst
101-111: NA (reserved)
Note: It needs RXQ FIFO Read command byte before each data burst.
4
0x0
RW
IUFFP IPV4/IPV6/UDP Fragment Frame Pass
When this bit is set, the KSZ8851SNL will pass the checksum check at receive side for
IPv4/IPv6 UDP frame with fragment extension header.
When this bit is cleared, the KSZ8851SNL will perform checksum operation based on
configuration and doesn’t care whether it’s a fragment frame or not.
3
0x0
RW
RXIUFCEZ Receive IPV4/IPV6/UDP Frame Checksum Equal Zero
When this bit is set, the KSZ8851SNL will pass the filtering for Ipv4/IPV6 UDP frame with
UDP checksum equal to zero.
When this bit is cleared, the KSZ8851SNL will drop IPV4/IPV6 UDP packet with UDP
checksum equal to zero.
2
0x1
RW
UDPLFE UDP Lite Frame Enable
When this bit is set, the KSZ8851SNL will check the checksum at receive side and
generate the checksum at transmit side for UDP Lite frame.
When this bit is cleared, the KSZ8851SNL will pass the checksum check at receive side
and skip the checksum generation at transmit side for UDP Lite frame.
相關PDF資料 |
PDF描述 |
|---|---|
| H3WWH-6406M | IDC CABLE - HPL64H/AE64M/HPL64H |
| M3UYK-2018R | IDC CABLE - MKS20K/MC20M/MPD20K |
| CDB5463U | BOARD EVAL & SOFTWARE CS5463 ADC |
| 2474R-25L | INDUCTOR 100UH POWER AXIAL |
| EBA36DRXH | CONN EDGECARD .125 DIP 72POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851SNL-BBE-EVL | 制造商:Micrel Inc 功能描述:BOARD EVAL MAC/PHY FOR KSZ8851 |
| KSZ8851SNL-EVAL | 功能描述:以太網開發工具 Single Ethernet Port + SPI Bus Interface(Lead Free) Eval Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8851SNL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851SNL |
| KSZ8851SNLI TR | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with SPI Bus Interface (I-Temp, Lead free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851SNLITR | 制造商:Micrel 功能描述:Ethernet Controller Single Chip 100Mbps |
發布緊急采購，3分鐘左右您將得到回復。