- 您現在的位置：買賣IC網 > PDF目錄381841 > FDC37B787-NS (STANDARD MICROSYSTEMS CORP) Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR PDF資料下載
參數資料
| 型號： | FDC37B787-NS |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP128 |
| 封裝： | ROHS COMPLIANT, QFP-128 |
| 文件頁數： | 93/249頁 |
| 文件大?。?/td> | 932K |
| 代理商： | FDC37B787-NS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁當前第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁
1.
93
The host selects an EPP register and drives
nIOR active.
The chip drives IOCHRDY inactive (low).
If WAIT is not asserted, the chip must wait
until WAIT is asserted.
The chip tri-states the PData bus and
deasserts nWRITE.
Chip asserts nDATASTB or nADDRSTRB
indicating that PData bus is tri-stated, PDIR is
set and the nWRITE signal is valid.
Peripheral drives PData bus valid.
Peripheral deasserts nWAIT, indicating that
PData is valid and the chip may begin the
termination phase of the cycle.
8. a) The chip latches the data from the PData
bus for the SData bus and deasserts
nDATASTB or nADDRSTRB. This marks
the beginning of the termination phase.
b) The chip drives the valid data onto the
SData bus and asserts (releases)
IOCHRDY allowing the host to complete
the read cycle.
9.
Peripheral tri-states the PData bus and
asserts nWAIT, indicating to the host that the
PData bus is tri-stated.
10. Chip may modify nWRITE, PDIR and
nPDATA in preparation for the next cycle.
EPP 1.7 OPERATION
When the EPP 1.7 mode is selected in the
configuration register, the standard and bi-
directional modes are also available. If no EPP
Read, Write or Address cycle is currently
executing, then the PDx bus is in the standard or
bi-directional mode, and all output signals
(STROBE, AUTOFD, INIT) are as set by the SPP
Control Port and direction is controlled by PCD of
the Control port.
In EPP mode, the system timing is closely coupled
to the EPP timing. For this reason, a watchdog
timer is required to prevent system lockup. The
timer indicates if more than 10usec have elapsed
from the start of the EPP cycle (nIOR or nIOW
asserted) to the end of the cycle nIOR or nIOW
deasserted). If a time-out occurs, the current EPP
2.
3.
4.
5.
6.
7.
cycle is aborted and the time-out condition is
indicated in Status bit 0.
Software Constraints
Before an EPP cycle is executed, the software
must ensure that the control register bits D0, D1
and D3 are set to zero. Also, bit D5 (PCD) is a
logic "0" for an EPP write or a logic "1" for and
EPP read.
EPP 1.7 Write
The timing for a write operation (address or data)
is shown in timing diagram EPP 1.7 Write Data or
Address cycle. IOCHRDY is driven active low
when nWAIT is active low during the EPP cycle.
This can be used to extend the cycle time. The
write cycle can complete when nWAIT is inactive
high.
Write Sequence of Operation
1.
The host sets PDIR bit in the control register
to a logic "0". This asserts nWRITE.
2.
The host selects an EPP register, places data
on the SData bus and drives nIOW active.
3.
The chip places address or data on PData
bus.
4.
Chip asserts nDATASTB or nADDRSTRB
indicating that PData bus contains valid
information, and the WRITE signal is valid.
5.
If
nWAIT
is
asserted,
deasserted until the peripheral deasserts
nWAIT or a time-out occurs.
6. When the host deasserts nIOW the chip
deasserts nDATASTB or nADDRSTRB and
latches the data from the SData bus for the
PData bus.
7.
Chip may modify nWRITE, PDIR and
nPDATA in preparation of the next cycle.
EPP 1.7 Read
The timing for a read operation (data) is shown in
timing diagram EPP 1.7 Read Data cycle.
IOCHRDY is driven active low when nWAIT is
active low during the EPP cycle. This can be used
to extend the cycle time. The read cycle can
complete when nWAIT is inactive high.
IOCHRDY
is
相關PDF資料 |
PDF描述 |
|---|---|
| FDC37B787QF | Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR |
| FDC37B78X | Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR |
| FDC37B80X | PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up |
| FDC37C665IR | 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support |
| FDC37C665GT | High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FDC37B787QF | 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR |
| FDC37B787QFP | 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| FDC37B78X | 制造商:SMSC 制造商全稱:SMSC 功能描述:Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR |
| FDC37B78X_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR |
| FDC37B802 | 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。