參數資料
型號： FDC37B787-NS
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 外設及接口
英文描述： Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
中文描述： MULTIFUNCTION PERIPHERAL, PQFP128
封裝： ROHS COMPLIANT, QFP-128
文件頁數： 106/249頁
文件大小： 932K
代理商： FDC37B787-NS
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁當前第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁
interrupt sharing. After a brief pulse low following
the interrupt event, the interrupt line is tri-stated so
that other interrupts may assert.
An interrupt is generated when:
1. For DMA transfers: When serviceIntr is 0,
dmaEn is 1 and the DMA TC is received.
2. For Programmed I/O:
a.
When serviceIntr is 0, dmaEn is 0,
direction
is
writeIntrThreshold or more free bytes in
the FIFO. Also, an interrupt is generated
when serviceIntr is cleared to 0 whenever
there are writeIntrThreshold or more free
bytes in the FIFO.
b.(1) When serviceIntr is 0, dmaEn is 0,
direction
is
readIntrThreshold or more bytes in the
FIFO. Also, an interrupt is generated
when serviceIntr is cleared to 0 whenever
there are readIntrThreshold or more
bytes in the FIFO.
3. When nErrIntrEn is 0 and nFault transitions
from high to low or when nErrIntrEn is set from
1 to 0 and nFault is asserted.
4. When ackIntEn is 1 and the nAck signal
transitions from a low to a high.
FIFO Operation
The FIFO threshold is set in the chip configuration
registers. All data transfers to or from the parallel
port can proceed in DMA or Programmed I/O
(non-DMA) mode as indicated by the selected
mode. The FIFO is used by selecting the Parallel
Port FIFO mode or ECP Parallel Port Mode. (FIFO
test mode will be addressed separately.) After a
reset, the FIFO is disabled. Each data byte is
transferred by a Programmed I/O cycle or PDRQ
depending
on
the
selection
Programmed I/O mode.
The following paragraphs detail the operation of
the FIFO flow control. In these descriptions,
<threshold> ranges from 1 to 16. The parameter
106
0
and
there
are
1
and
there
are
of
DMA
or
FIFOTHR, which the user programs, is one less
and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer
periods of time between service requests, but
requires faster servicing of the request for both
read and write cases. The host must be very
responsive to the service request. This is the
desired case for use with a "fast" system. A high
value of threshold (i.e. 12) is used with a "sluggish"
system by affording a long latency period after a
service request, but results in more frequent
service requests.
DMA TRANSFERS
DMA transfers are always to or from the ecpDFifo,
tFifo or CFifo. DMA utilizes the standard PC DMA
services. To use the DMA transfers, the host first
sets up the direction and state as in the
programmed I/O case. Then it programs the DMA
controller in the host with the desired count and
memory address. Lastly it sets dmaEn to 1 and
serviceIntr to 0. The ECP requests DMA transfers
from the host by activating the PDRQ pin. The
DMA will empty or fill the FIFO using the
appropriate direction and mode. When the
terminal count in the DMA controller is reached, an
interrupt is generated and serviceIntr is asserted,
disabling DMA. In order to prevent possible
blocking of refresh requests dReq shall not be
asserted for more than 32 DMA cycles in a row.
The FIFO is enabled directly by asserting
nPDACK and addresses need not be valid. PINTR
is generated when a TC is received. PDRQ must
not be asserted for more than 32 DMA cycles in a
row. After the 32nd cycle, PDRQ must be kept
unasserted until nPDACK is deasserted for a
minimum of 350nsec. (Note: The only way to
properly terminate DMA transfers is with a TC.)
DMA may be disabled in the middle of a transfer
by first disabling the host DMA controller. Then
setting serviceIntr to 1, followed by setting dmaEn
to 0, and waiting for the FIFO to become empty or
full. Restarting the DMA is accomplished by
enabling DMA in the host, setting dmaEn to 1,
followed by setting serviceIntr to 0.
相關PDF資料
PDF描述
FDC37B787QF Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B78X Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B80X PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up
FDC37C665IR 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
相關代理商/技術參數
參數描述
FDC37B787QF 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B787QFP 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37B78X 制造商:SMSC 制造商全稱:SMSC 功能描述:Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B78X_07 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B802 制造商:Rochester Electronics LLC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*