參數資料
型號： FDC37B787-NS
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 外設及接口
英文描述： Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
中文描述： MULTIFUNCTION PERIPHERAL, PQFP128
封裝： ROHS COMPLIANT, QFP-128
文件頁數： 64/249頁
文件大?。?/td> 932K
代理商： FDC37B787-NS
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁
CONTROL COMMANDS
Control
commands
commands in that no data transfer takes place.
Three commands generate an interrupt when
complete: Read ID, Recalibrate, and Seek. The
other control commands do not generate an
interrupt.
Read ID
The Read ID command is used to find the present
position of the recording heads. The FDC stores
the values from the first ID field it is able to read
into its registers. If the FDC does not find an ID
address mark on the diskette after the second
occurrence of a pulse on the nINDEX pin, it then
sets the IC code in Status Register 0 to "01"
(abnormal termination), sets the MA bit in Status
Register 1 to "1", and terminates the command.
The following commands will generate an interrupt
upon completion. They do not return any result
bytes. It is highly recommended that control
commands be followed by the Sense Interrupt
Status command. Otherwise, valuable interrupt
status information will be lost.
Recalibrate
This command causes the read/write head within
the FDC to retract to the track 0 position. The
FDC clears the contents of the PCN counter and
checks the status of the nTR0 pin from the FDD.
As long as the nTR0 pin is low, the DIR pin
remains 0 and step pulses are issued. When the
nTR0 pin goes high, the SE bit in Status Register
0 is set to "1" and the command is terminated. If
the nTR0 pin is still low after 79 step pulses have
been issued, the FDC sets the SE and the EC bits
of Status Register 0 to "1" and terminates the
command. Disks capable of handling more than
80 tracks per side may require more than one
Recalibrate command to return the head back to
physical Track 0.
The Recalibrate command does not have a result
phase. The Sense Interrupt Status command
must be issued after the Recalibrate command to
effectively terminate it and to provide verification of
the head position (PCN). During the command
64
differ
from
the
other
phase of the recalibrate operation, the FDC is in
the BUSY state, but during the execution phase it
is in a NON-BUSY state. At this time, another
Recalibrate command may be issued, and in this
manner parallel Recalibrate operations may be
done on up to four drives at once.
Upon power up, the software must issue a
Recalibrate command to properly initialize all
drives and the controller.
Seek
The read/write head within the drive is moved from
track to track under the control of the Seek
command. The FDC compares the PCN, which is
the current head position, with the NCN and
performs the following operation if there is a
difference:
PCN < NCN: Direction signal to drive set to
"1" (step in) and issues step pulses.
PCN > NCN: Direction signal to drive set to
"0" (step out) and issues step pulses.
The rate at which step pulses are issued is
controlled by SRT (Stepping Rate Time) in the
Specify command. After each step pulse is
issued, NCN is compared against PCN, and when
NCN = PCN the SE bit in Status Register 0 is set
to "1" and the command is terminated. During the
command phase of the seek or recalibrate
operation, the FDC is in the BUSY state, but
during the execution phase it is in the NON-BUSY
state. At this time, another Seek or Recalibrate
command may be issued, and in this manner,
parallel seek operations may be done on up to four
drives at once.
Note that if implied seek is not enabled, the read
and write commands should be preceded by:
1) Seek command - Step to the proper track
2) Sense Interrupt Status command - Terminate
the Seek command
3) Read ID - Verify head is on proper track
4) Issue Read/Write command.
The Seek command does not have a result phase.
Therefore, it is highly recommended that the
相關PDF資料
PDF描述
FDC37B787QF Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B78X Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B80X PC98/99 Compliant Enhanced Super I/O Controller with Keyboard/Mouse Wake-Up
FDC37C665IR 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
相關代理商/技術參數
參數描述
FDC37B787QF 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B787QFP 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37B78X 制造商:SMSC 制造商全稱:SMSC 功能描述:Enhanced Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B78X_07 制造商:SMSC 制造商全稱:SMSC 功能描述:Super I/O Controller with ACPI Support, Real Time Clock and Consumer IR
FDC37B802 制造商:Rochester Electronics LLC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*