參數資料
型號： DS80C411-FNY+
廠商： Maxim Integrated Products
文件頁數： 89/102頁
文件大?。?/td> 0K
描述： IC MCU 75MHZ 16MB HP 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
系列： 80C
核心處理器： 8051
芯體尺寸： 8-位
速度： 75MHz
連通性： 1 線，CAN，EBI/EMI，以太網，SIO，UART/USART
外圍設備： 電源故障復位，WDT
輸入/輸出數： 64
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： ROM
RAM 容量： 64K x 8
電壓 - 電源 (Vcc/Vdd)： 1.62 V ~ 3.6 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-LQFP
包裝： 托盤
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
87 of 102
CAN Interrupts
The DS80C410 provides one interrupt source for the CAN controller. The CAN interrupt source can be triggered by
a receive/transmit acknowledgment from one of the 15 message centers or an error condition.
Each message center has individual ETI (transmit) and ERI (receive) interrupt enable bits and INTRQ flag bits that
are found in the corresponding message control (C0MxC) SFR. If the ETI or ERI bits have been set for a message
center, the successful transmission or receipt of a message, respectively, sets the INTRQ bit for that message
center. The INTRQ bit can only be cleared through software. All message center interrupt flags (INTRQ) of the
CAN module are ORed together to produce a single interrupt source for the CAN controller. For the microcontroller
to acknowledge any individual message center interrupt request, the global interrupt enable bit (IE.7) and the CAN
0 interrupt enable bit, EIE.6, must both be set.
Interrupt assertion of error and status conditions associated with the CAN module is controlled by the ERIE and
STIE bits located in the CAN 0 control (C0C) SFR. These interrupt sources also require that the global interrupt
enable (EA = IE.7) and the CAN 0 interrupt enable (C0IE = EIE.6) bits be set in order to be acknowledged by the
microcontroller.
Arbitration and Masking
After the CAN module has ascertained that an incoming message is bit error-free, the identification field of that
message is then compared against one or more arbitration values to determine if they are loaded into a message
center. Each enabled message center (see the MSRDY bit in the CAN message control register) is tested in order
from 1 to 15. The first message center to successfully pass the test receives the incoming message and ends the
testing. The use of masking registers allows the use of more complex identification schemes, as tests can be made
based on bit patterns rather than an exact match between all bits in the identification field and arbitration values.
The CAN controller also incorporates a set of five masks to allow messages with different IDs to be grouped and
successfully loaded into a message center; note that some of these masks are optional as per the bits shown in
There are several possible arbitration tests, varying according to which message center is involved. If all of the
enabled tests succeed, the message is loaded into the respective message center. The most basic test, performed
on all messages, compares either 11 (CAN 2.0A) or 29 (CAN 2.0B) bits of the identification field to the appropriate
arbitration register, based on the EX/ST bit in the CAN 0 format register. The MEME bit (C0MxF.1) controls whether
the arbitration and ID registers are compared directly or through a mask register. A special set of arbitration
registers dedicated to message center 15 allows added flexibility in filtering this location.
If desired, further arbitration can be performed by comparing the first two bytes of the data field in each message
against two 8-bit media arbitration register bytes. The MDME bit in the CAN message center format registers
(C0MxF.0) either disables (MDME = 0) arbitration, or enables (MDME = 1) arbitration using the media ID mask
registers 0–1.
If the 11-bit or 29-bit arbitration and the optional media-byte arbitration are successful, the message is loaded into
the respective message center. The format register also allows the microcontroller to program each message
center to function in a receive or transmit mode through the T/R bit and to use from 0 to 8 data bytes within the data
field of a message. Note that message center 15 can only be used in a receive mode. To avoid a priority inversion,
the DS80C410 CAN controller is configured to reload the transmit buffer with the message of the highest priority
(lowest message center number) whenever an arbitration is lost or an error condition occurs.
相關PDF資料
PDF描述
MS27468T17B55PA CONN RCPT 55POS JAM NUT W/PINS
DS87C520-MNL+ IC MCU EPROM/ROM 33MH IND 40-DIP
DS87C530-QCL+ IC MCU EPR/ROM W/RTC 33MZ 52PLCC
DS80C320-MCL+ IC MCU HI SPEED 33MHZ 40-DIP
MS27513E18B35S CONN RCPT 66POS BOX MNT W/SCKT
相關代理商/技術參數
參數描述
DS80C411-FNY+ 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80CH11 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager
DS80CH11+E02 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11+E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11+E02 System Energy Managers
DS80CH11-E02 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11-E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11-E02 System Energy Managers
DS80E100 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*