- 您現在的位置：買賣IC網 > PDF目錄11785 > DS80C411-FNY+ (Maxim Integrated Products)IC MCU 75MHZ 16MB HP 100-LQFP PDF資料下載
參數資料
| 型號： | DS80C411-FNY+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 74/102頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 75MHZ 16MB HP 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 系列： | 80C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 75MHz |
| 連通性： | 1 線，CAN，EBI/EMI，以太網，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 64 |
| 程序存儲器容量： | 64KB（64K x 8） |
| 程序存儲器類型： | ROM |
| RAM 容量： | 64K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-LQFP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁當前第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
73 of 102
Figure 12. Wake-Up Frame-Filter Structure
31
0
FILTER 0 BYTE MASK
FILTER 1 BYTE MASK
FILTER 2 BYTE MASK
FILTER 3 BYTE MASK
RESERVED
FILTER 3
COMMAND
RESERVED
FILTER 2
COMMAND
RESERVED
FILTER 1
COMMAND
RESERVED
FILTER 0
COMMAND
FILTER 3 OFFSET
FILTER 2 OFFSET
FILTER 1 OFFSET
FILTER 0 OFFSET
FILTER 1 CRC-16
FILTER 0 CRC-16
FILTER 3 CRC-16
FILTER 2 CRC-16
Embedded ROM Firmware
The DS80C410 incorporates an embedded ROM specifically designed for hosting the MxTNI runtime
environment and the MxTNI C libraries. The ROM firmware implements three major components: a full TCP/IPv4/6
stack with industry-standard Berkeley socket interface, a preemptive task scheduler, and NetBoot functionality. The
NetBoot component uses the TCP/IP stack, socket layer, and task scheduler to provide automatic network boot
capability. NetBoot allows an application to be downloaded from the network and executed by the microcontroller.
To use the ROM firmware, the system is required to have the following hardware components:
64kB SRAM memory, internal on the DS80C410 and DS80C411, mapped (Note 1) at address locations
000000h–00FFFFh
Memory (SRAM or flash) to store user-application code
DS2502P-E48 1-Wire chip, to hold physical MAC address (Note 2)
External crystal or oscillator (Note 3)
Note 1:
Merged program/data memory configuration is required.
Note 2:
Java applications and NetBoot require a DS2502P-E48. Applications written in C can program the MAC address directly and do not
require the use of the DS2502P-E48.
Note 3:
NetBoot functionality requires external clock frequency to be at least 7MHz. Clock doubler is not turned on until after NetBoot. Thus,
100Mbps NetBoot is not possible unless the external clock source is at least 25MHz. When not in NetBoot, the system clock
(external clock source after internal multiplication or division) must be a minimum of 25MHz for use of the Ethernet 100Mbps mode.
Selecting DS80C410 ROM Code Execution
The DS80C410, following each reset, begins execution of program code at address location 000000h. Since the
DS80C410 contains internal ROM and supports external program code, the user must select which of these two
program memory spaces should be accessed for initial program fetching. There are two mechanisms that control
selection of the internal DS80C410 ROM code. These two controls are the EA pin and the bypass ROM (BROM)
SFR bit. No matter the state of the BROM bit, if the EA pin is held at a logic low level, the DS80C410 ROM code is
not entered and is not accessible to the user code. If the EA pin is at a logic high level, the BROM bit is then
examined to determine whether the internal DS80C410 ROM should be executed or bypassed. If BROM = 0, the
ROM code is executed. Otherwise (BROM = 1), the ROM code is bypassed and execution is transferred to external
user code at address 000000h. The BROM bit defaults to 0 on a power-on reset, but is unaffected by other reset
sources. This code selection process can be seen in Figure 13.
DS80C410 ROM Code Execution Flow
Once the internal DS80C410 ROM code has been selected (EA = 1, BROM = 0), it must first execute some basic
configuration code to provide functionality to subsequent ROM operations. Next, the ROM code reads the state of
port pin P1.7. The ROM associates the logic state of P1.7 with the user desire to invoke the serial loader function. If
the serial loader pin (P1.7) is a logic 1, the ROM monitors for activity on serial port 0 and tries to respond to the
external host with its own serial banner. Once serial communication has been established at a supported baud
rate, signified by correct reception of the DS80C410 loader banner and prompt, the user can issue commands. The
serial loader commands are described later in the data sheet. If the serial loader pin is pulled to a logic 0, the ROM
reads the state of port pin P5.3. Much like the association made between P1.7 and invocation of the serial loader,
the ROM links the logic state of P5.3 with the user desire to begin the NetBoot process. If the NetBoot pin (P5.3) is
asserted (logic 0), the ROM initiates the NetBoot process. If the NetBoot pin is not asserted (logic 1), the ROM
MxTNI is a trademark of Maxim Integrated Products, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27468T17B55PA | CONN RCPT 55POS JAM NUT W/PINS |
| DS87C520-MNL+ | IC MCU EPROM/ROM 33MH IND 40-DIP |
| DS87C530-QCL+ | IC MCU EPR/ROM W/RTC 33MZ 52PLCC |
| DS80C320-MCL+ | IC MCU HI SPEED 33MHZ 40-DIP |
| MS27513E18B35S | CONN RCPT 66POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C411-FNY+ | 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80CH11 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager |
| DS80CH11+E02 | 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11+E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11+E02 System Energy Managers |
| DS80CH11-E02 | 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11-E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11-E02 System Energy Managers |
| DS80E100 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables |
發布緊急采購，3分鐘左右您將得到回復。