參數資料
型號： DS80C411-FNY+
廠商： Maxim Integrated Products
文件頁數： 69/102頁
文件大?。?/td> 0K
描述： IC MCU 75MHZ 16MB HP 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
系列： 80C
核心處理器： 8051
芯體尺寸： 8-位
速度： 75MHz
連通性： 1 線，CAN，EBI/EMI，以太網，SIO，UART/USART
外圍設備： 電源故障復位，WDT
輸入/輸出數： 64
程序存儲器容量： 64KB（64K x 8）
程序存儲器類型： ROM
RAM 容量： 64K x 8
電壓 - 電源 (Vcc/Vdd)： 1.62 V ~ 3.6 V
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-LQFP
包裝： 托盤
DS80C410/DS80C411 Network Microcontrollers with Ethernet and CAN
69 of 102
Transmit/Receive Status Words
For each attempt made by the MAC to receive or transmit packet data, the BCU writes a 32-bit transmit or receive
status word back to the first word of the starting page for the packet. This word provides status information needed
by the CPU to determine when and what action should be taken.
Transmit Status Word
Bit Names:
31
RETRY
—
24
23
—
16
15
—
HBF
COL_CNT [3:0]
OLTCOL
DFR
8
7
NODAT
XCOL
LTCOL
XDFR
LSCRS
NOCRS
JABTO
ABORT
0
RETRY, Packet Retry. This bit indicates that the current transmit packet has to be retried because of a collision on
the bus. The application has to restart the transmission of the frame when this bit is set to 1. When this bit is reset,
it indicates that the transmission of the current frame is completed. The success or failure to transmit a frame is
indicated by the framed aborted (ABORT) bit.
HBF, Heart-Beat Fail. This bit is only meaningful for ENDEC mode. This bit is not valid if the NODAT or XFDR bit
is set.
0 = heart-beat collision check successful
1 = heart-beat collision check failed
COL_CNT [3:0], Collision Count. These four bits indicate the number of collisions that occurred before the frame
was transmitted. Collision count is valid only in half-duplex mode and it is not valid when the excessive collisions
(XCOL) bit is set.
OLTCOL, Late Collision Observed. This bit is only valid in half-duplex mode and is always set if the late collision
abort (LTCOL) bit is set in the status word.
0 = no late collisions observed
1 = late collision (collision after the first time slot) observed.
DFR, Deferred. This bit is only valid in half-duplex mode.
0 = no deferral required for the frame transmission attempt
1 = MAC had to defer while waiting to transmit because the carrier was not idle
NODAT, Underrun
0 = transmit frame was not aborted due to data underrun
1 = transmit frame aborted because the MAC did not have sufficient data to complete the current frame
transmission
XCOL, Excessive Collisions. This bit is only valid in half-duplex mode.
0 = transmit frame was not aborted due to excessive collisions
1 = transmit frame aborted because of excessive collisions (16 transmit attempts unless DRTY = 1)
LTCOL, Late Collision. This bit is only valid in half-duplex mode.
0 = transmit frame was not aborted due to a late collision
1 = transmit frame aborted due to collision occurring after the collision window of 64 Bytes. This bit is not valid if the
NODAT bit is set.
XDFR, Excessive Deferral. This bit is only valid in half-duplex mode when the MAC control register bit DFR is set.
0 = transmit frame was not aborted due to excessive deferral
1 = transmit frame aborted due to deferral of over 24,288 bit times
LSCRS, Loss of Carrier. This bit is only valid in half-duplex mode.
0 = transmit frame was not aborted due to loss of carrier
1 = transmit frame aborted due to loss of carrier (CRS = 0 during the frame transmission)
相關PDF資料
PDF描述
MS27468T17B55PA CONN RCPT 55POS JAM NUT W/PINS
DS87C520-MNL+ IC MCU EPROM/ROM 33MH IND 40-DIP
DS87C530-QCL+ IC MCU EPR/ROM W/RTC 33MZ 52PLCC
DS80C320-MCL+ IC MCU HI SPEED 33MHZ 40-DIP
MS27513E18B35S CONN RCPT 66POS BOX MNT W/SCKT
相關代理商/技術參數
參數描述
DS80C411-FNY+ 功能描述:8位微控制器 -MCU Network MCU w/Ethernet & CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80CH11 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:System Energy Manager
DS80CH11+E02 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11+E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11+E02 System Energy Managers
DS80CH11-E02 制造商:Maxim from Components Direct 功能描述:MAXIM DS80CH11-E02 SYSTEM ENERGY MANAGERS - Trays 制造商:Maxim 功能描述:Maxim DS80CH11-E02 System Energy Managers
DS80E100 制造商:NSC 制造商全稱:National Semiconductor 功能描述:5 to 12.5 Gbps, Power-Saver Equalizer for Backplanes and Cables
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*