參數資料
型號: COM20019ILJP
廠商: STANDARD MICROSYSTEMS CORP
元件分類: 微控制器/微處理器
中文描述: 1 CHANNEL(S), 312.5K bps, LOCAL AREA NETWORK CONTROLLER, PQCC28
封裝: PLASTIC, LCC-28
文件頁數: 64/65頁
文件大?。?/td> 386K
代理商: COM20019ILJP
Cost Competitive ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM
Rev. 09-25-07
Page 8
SMSC COM20019I
DATASHEET
Chapter 3
DESCRIPTION OF PIN FUNCTIONS
PLCC PIN
NO.
NAME
SYMBOL
DESCRIPTION
MICROCONTROLLER INTERFACE
1-3
Address
0-2
A0/nMUX,
A1,A2/ALE
Input. On a non-multiplexed mode, A0-A2 are
address input bits. (A0 is the LSB) On a
multiplexed address/data bus, nMUX tied Low,
A1 is left open, and ALE is tied to the Address
Latch Enable signal. A1 is connected to an
internal pull-up resistor.
4-6,8-12
Data 0-7
AD0-AD2, D3-
D7
Input/Output. On a non-multiplexed bus, these
signals are used as the data lines for the
device. On a multiplexed address/data bus,
AD0-AD2 act as the address lines (latched by
ALE) and as the low data lines for the device.
D3-D7 are always used for data only. These
signals are connected to internal pull-up
resistors.
27
nRead/nData
Strobe
nRD/nDS
Input. On a 68XX-like bus, nDS is an active
low signal issued by the microcontroller as the
data strobe signal to strobe the data onto the
bus. On a 80XX-like bus, nRD is an active low
signal issued by the microcontroller to indicate
a read operation.
26
nWrite/
Direction
nWR/DIR
Input. On a 68XX-like bus, DIR is issued by
the microcontroller as the Read/nWrite signal
to determine the direction of data transfer. In
this case, a logic "1" selects a read operation,
while a logic "0" selects a write operation. In
this case, data is actually strobed by the nDS
signal. On an 80XX-like bus, nWR is an active
low signal issued by the microcontroller to
indicate a write operation. In this case, a logic
"0" on this pin, when the COM20019I is
accessed, enables data from the data bus to
be written to the device.
23
nReset in
nRESET
Input. This active low signal executes a
hardware reset.
24
nInterrupt
nINTR
Output. This active low signal is generated by
the COM20019I when an enabled interrupt
condition occurs.
25
nChip Select
nCS
Input. This active low signal selects the
COM20019I for an access.
相關PDF資料
PDF描述
CP0603A2442CSTR
CP0805A0881ESTR
CP0805A1441BSTR
CP2101-GMR
CP2101
相關代理商/技術參數
參數描述
COM20019I-LJP 制造商:SMSC 制造商全稱:SMSC 功能描述:Low Cost ARCNET(ANSI 878.1) Controller with 2k X 8 On-Board RAM
COM20019ILJP3V 功能描述:網絡控制器與處理器 IC ARCNET Contrllr RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
COM20019ILJPTR 功能描述:網絡控制器與處理器 IC Arcnet (ANSI 878.1) Controllr 2k x 8 Ram RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
COM20019IP 制造商:Rochester Electronics LLC 功能描述:- Bulk
COM20020 制造商:SMSC 制造商全稱:SMSC 功能描述:COM20020 3.3V ULANC Universal Local Area Network Controller with 2K x 8 On-Board RAM