- 您現在的位置：買賣IC網 > PDF目錄26505 > COM20019ILJP (STANDARD MICROSYSTEMS CORP) PDF資料下載
參數資料
| 型號： | COM20019ILJP |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 微控制器/微處理器 |
| 中文描述： | 1 CHANNEL(S), 312.5K bps, LOCAL AREA NETWORK CONTROLLER, PQCC28 |
| 封裝： | PLASTIC, LCC-28 |
| 文件頁數： | 22/65頁 |
| 文件大小： | 386K |
| 代理商： | COM20019ILJP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
Cost Competitive ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM
SMSC COM20019I
Page 29
Rev. 09-25-07
DATASHEET
BIT
BIT NAME
SYMBOL
DESCRIPTION
2
Tentative ID
TENTID
This bit, if high, indicates that a response to a token whose DID
matches the value in the Tentative ID Register has occurred.
The second DID and the trailing zero's are not checked. Since
each node sees every token passed around the network, this
feature can be used with the device on-line in order to build and
update a network map. Refer to the Improved Diagnostics
section for further detail.
1
New Next ID
NEW
NXTID
This bit, if high, indicates that the Next ID Register has been
updated and that a node has either joined or left the network.
Reading the Diagnostic Status Register does not clear this bit.
This bit, when set, will cause an interrupt if the corresponding bit
in the IMR is also set. The bit is cleared by reading the Next ID
Register.
1,0
(Reserved)
These bits are undefined.
Table 6.5 - Command Register
DATA
COMMAND
DESCRIPTION
0000 0000
Clear
Transmit
Interrupt
This command is used only in the Command Chaining
operation. Please refer to the Command Chaining section for
definition of this command.
0000 0001
Disable
Transmitter
This command will cancel any pending transmit command
(transmission that has not yet started) and will set the TA
(Transmitter Available) status bit to logic "1" when the
COM20019I next receives the token.
0000 0010
Disable
Receiver
This command will cancel any pending receive command. If the
COM20019I is not yet receiving a packet, the RI (Receiver
Inhibited) bit will be set to logic "1" the next time the token is
received. If packet reception is already underway, reception will
run to its normal conclusion.
b0fn n100
Enable
Receive to
Page fnn
This command allows the COM20019I to receive data packets
into RAM buffer page fnn and resets the RI status bit to logic
"0". The values placed in the "nn" bits indicate the page that the
data will be received into (page 0, 1, 2, or 3). If the value of "f"
is a logic "1", an offset of 256 bytes will be added to that page
specified in "nn", allowing a finer resolution of the buffer. Refer
to the Selecting RAM Page Size section for further detail. If the
value of "b" is logic "1", the device will also receive broadcasts
(transmissions to ID zero). The RI status bit is set to logic "1"
upon successful reception of a message.
00fn n011
Enable
Transmit from
Page fnn
This command prepares the COM20019I to begin a transmit
sequence from RAM buffer page fnn the next time it receives
the token. The values of the "nn" bits indicate which page to
transmit from (0, 1, 2, or 3). If "f" is logic "1", an offset of 256
bytes is the start of the page specified in "nn", allowing a finer
resolution of the buffer. Refer to the Selecting RAM Page Size
section for further detail. When this command is loaded, the TA
and TMA bits are reset to logic "0". The TA bit is set to logic "1"
upon completion of the transmit sequence. The TMA bit will
have been set by this time if the device has received an ACK
from the destination node. The ACK is strictly hardware level,
sent by the receiving node before its microcontroller is even
aware of message reception. Refer to Figure 1 for details of the
transmit sequence and its relation to the TA and TMA status
bits.
相關PDF資料 |
PDF描述 |
|---|---|
| CP0603A2442CSTR | |
| CP0805A0881ESTR | |
| CP0805A1441BSTR | |
| CP2101-GMR | |
| CP2101 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COM20019I-LJP | 制造商:SMSC 制造商全稱:SMSC 功能描述:Low Cost ARCNET(ANSI 878.1) Controller with 2k X 8 On-Board RAM |
| COM20019ILJP3V | 功能描述:網絡控制器與處理器 IC ARCNET Contrllr RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| COM20019ILJPTR | 功能描述:網絡控制器與處理器 IC Arcnet (ANSI 878.1) Controllr 2k x 8 Ram RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| COM20019IP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| COM20020 | 制造商:SMSC 制造商全稱:SMSC 功能描述:COM20020 3.3V ULANC Universal Local Area Network Controller with 2K x 8 On-Board RAM |
發布緊急采購，3分鐘左右您將得到回復。