- 您現在的位置：買賣IC網 > PDF目錄385094 > AK4673EG (Asahi Kasei Microsystems Co.,Ltd) Stereo CODEC with MIC/HP-AMP and Touch Screen Controller PDF資料下載
參數資料
| 型號： | AK4673EG |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 元件分類： | Codec |
| 英文描述： | Stereo CODEC with MIC/HP-AMP and Touch Screen Controller |
| 中文描述： | 立體聲編解碼器麥克風/惠普- AMP及觸摸屏控制器 |
| 文件頁數： | 78/107頁 |
| 文件大小： | 1171K |
| 代理商： | AK4673EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁
[AK4673]
MS0670-E-00
2007/09
- 78 -
■
Pen Interrupt
The AK4673 has a pen-interrupt function to detect the pen touch on the touch panel. This function will be used as the
interrupt of the microprocessor. Pen interrupt function is enabled at power-down state. YN driver is on and this pin is
connected to GND at the power down state. And the XP pin is pulled up via an internal resister (Ri), typically 10K
Ω
. If
the touch plate is touched by pen or stylus, the current flows via <VCC>-<Ri>-<XP>-<the plates>-<YN>-<GND>. The
resistance of the plate is generally 1K
Ω
or less, the PENIQRN pin is force to “L” level. If the pen is released, the
PENIRQN pin returns “H” level because two plates are disconnected, and the current does not flow via two plates.
The transition of PENIRQN is related to PD0 bit. PD0 bit is updated as shown below. (Please see “power-down control”
for the detail. Once the control command PD0= “1” is sent the pen-interrupt function is disabled.
The clock number under the write and the read operation refer to
Figure 74
and
Figure 14
.
I.
The period from start condition to SCL7
↓
The level transition of the PENIRQN pin is determined by PD0 bit of the previous command. When the previous
command with PD0= “0” the pen-interrupt function will be enabled. The PENIRQN pin is low when the panel is
touch, the PENIRQN pin is “H” when the panel is untouched. When the previous command with PD0= “1” is
sent PENIRQN pin is low regardless of pen-touch
II.
The period SCL7
↓
to SCL8
↑
on the write operation
The level of the PENIRQN pin is always low regardless of PD0 bit and the state of panel (touched/untouched)
III.
The period from SCL8
↑
to SCL18
↓
on the write operation
The level transition of the PENIRQN pin is determined by PD0 bit of the previous command. When the previous
command with PD0= “0” the pen-interrupt function will be enabled. The PENIRQN pin is low when the panel is
touch, the PENIRQN pin is “H” when the panel is untouched. When the previous command with PD0= “1” is
sent PENIRQN pin is low regardless of pen-touch
IV.
The period from SCL18
↓
on the write operation to SCL7
↓
on the read operation
The level of PENIRQN pin is determined by the A2 bit and PD0 bit of the present command. The PENIRQN pin
is always low regardless pen-touch when command with A2 = “1” or PD0 = “1” is set. The PENIRQN is
determined by the pen-touch (touched/untouched) when command with A2= “1” and PD0= “1” is sent.
V.
The period from SCL7
↓
to SCL21
↓
on the write operation
The AD input will sample the hold and the conversion will be done during this period. PENIRQN is always low.
VI.
The period after SCL21
↓
on the read operation
The level transition of the PENIRQN pin is determined by PD0 bit of the present command. When the present
command PD0= “0” is sent the pen-interrupt function will be enabled. The PENIRQN pin is low when the panel
is touched. The PENIRQN pin is “H” when the panel is untouched. When the present command PD0= “1” are
sent the PENIRQN pin is low regardless of pen-touch.
It is recommended that the processor will mask the pseudo interrupt while the control command is issued or AD data is
sent to processor.
XP
PENIRQN
Driver ON
YN
EN2
Ri =
10k
Ω
Driver OFF
EN1
VCC
VCC
VCC
PEN Interrupt
To uP
Figure 76 Pen interrupt function block
相關PDF資料 |
PDF描述 |
|---|---|
| AK4682 | Multi-channel CODEC with 2Vrms Stereo Selector |
| AK4682EQ | Multi-channel CODEC with 2Vrms Stereo Selector |
| AK4683_07 | Asynchronous Multi-Channel Audio CODEC with DIR/T |
| AK4683EQ | Asynchronous Multi-Channel Audio CODEC with DIR/T |
| AK4683 | Asynchronous Multi-Channel Audio CODEC with DIR/T |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4675 | 制造商:AKM 制造商全稱:AKM 功能描述:Stereo CODEC with MIC/RCV/HP/SPK-AMP |
| AK4675EG | 制造商:AKM 制造商全稱:AKM 功能描述:Stereo CODEC with MIC/RCV/HP/SPK-AMP |
| AK4682 | 制造商:AKM 制造商全稱:AKM 功能描述:Multi-channel CODEC with 2Vrms Stereo Selector |
| AK4682AEQ | 功能描述:IC CODEC MULTI-CHANNEL 48LQFP 制造商:akm semiconductor inc. 系列:* 零件狀態:上次購買時間 標準包裝:1,000 |
| AK4682EQ | 制造商:AKM 制造商全稱:AKM 功能描述:Multi-channel CODEC with 2Vrms Stereo Selector |
發布緊急采購，3分鐘左右您將得到回復。