- 您現在的位置：買賣IC網 > PDF目錄385092 > AK4516AVF (Asahi Kasei Microsystems Co.,Ltd) 3V 16BIT ADC&DAC WITH BUILT-IN PGA PDF資料下載
參數資料
| 型號： | AK4516AVF |
| 廠商： | Asahi Kasei Microsystems Co.,Ltd |
| 英文描述： | 3V 16BIT ADC&DAC WITH BUILT-IN PGA |
| 中文描述： | 3V的16位ADC |
| 文件頁數： | 19/39頁 |
| 文件大小： | 355K |
| 代理商： | AK4516AVF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
ASAHI KASEI
[AK4516A]
M0026-E-00
1998/08
- 19 -
3. Full-auto Mode
The full-auto mode is done automatically by the auto limitter and the auto recovery function of the AK4516A.
However, writing to the register is needed to enable these functions.
During the full-auto mode, writing to the following registers from uP is inhibited.
LRGA, LTM1-0, ZELM, LMTH1-0, LMAT2-0, WTM1-0, NRTM1-0, RATT1-0, ZENM, REF6-0, IPGL, IPGR
Figure 9 . Control example of full-auto mode operation (LMAT=RATT: 1 step, ZENM=ZELM="1")
1
{
Set-up the registers of full-auto mode
(LTM1-0, ZELM, LMTH1-0, LMAT2-0, WTM1-0, RATT1-0, NRTM1-0, ZENM, REF6-0, GSEL, IPGL,
IPGR, LRGA="1")
2
{
WR(LMTE=RCVE="1"): After the registers concerned in the auto limitter operation is set up and
confirming the zero crossing flags(ZFIPL, ZFIPR)="1", LMTH and RCVE are set "1".
3
{
WR(IPGA="31H"):As the operation is full-auto mode, writing by uP is ignored.
4
{
The ready of recovery starts.
5
{
As the input signal of ADC exceeds LMTH, the recovery operation (in the figure, recovery ready) is
discontinued and the limitter operation starts.
6
{
WR(LMTE=RCVE="0"):The full-auto mode operation is completed.
7
{
In Figure 9 , since "0" is written to LMTE& RCVE during the ATT operation, the operation changes to the
manual mode after completing ATT operation. After confirming LCDET="1", it is possible to change the
each register set-up. If LMTE&RCVE are set "0" during the full-auto mode operation, LCDET becomes
"1" after the max "1" ATT/GAIN operation is completed by internal state.
8
{
In this case, the input signal of ADC exceeds LMTH, the auto limitter does not operate because of
LMTE=RCVE="0".
9
{
After the limitter operation is completed, the AK4516A waits for the time set by WTM1-0. If the input
signal does not exceed (LMTH - 2dB), the recovery operation is executed. After the waiting time finishes
the next waiting time starts immediately. In recovery ready, the waiting timer is reset under the condition
of (LMTH - 2dB)
≤
Input Signal<LMTH. And the timer starts under the condition of (LMTH - 2dB)>Input
Signal.
相關PDF資料 |
PDF描述 |
|---|---|
| AK4522 | 20BIT STEREO ADC & DAC |
| AK4522VF | 20BIT STEREO ADC & DAC |
| AK4523 | 20BIT STEREO ADC & DAC |
| AK4523VF | 20BIT STEREO ADC & DAC |
| AK4524 | 24BIT 96KHZ AUDIO CODEC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AK4516AVFP-E1 | 制造商:Asahi Kasei Microsystems Co Ltd 功能描述: |
| AK4520 | 制造商:AKM 制造商全稱:AKM 功能描述:100dB 20Bit Stereo ADC & DAC |
| AK4520A | 制造商:AKM 制造商全稱:AKM 功能描述:EVALUATION BOARD REV.B FOR AK4520A |
| AK4520A-VF | 制造商:AKM 制造商全稱:AKM 功能描述:100dB 20Bit Stereo ADC & DAC |
| AK4522 | 制造商:AKM 制造商全稱:AKM 功能描述:20Bit Stereo ΔΣ ADC & DAC |
發布緊急采購，3分鐘左右您將得到回復。