- 您現在的位置：買賣IC網 > PDF目錄12016 > ADUC7121BBCZ (Analog Devices Inc)IC ARM7TDMI MCU 126KB 108CSPBGA PDF資料下載
參數資料
| 型號： | ADUC7121BBCZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 80/96頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ARM7TDMI MCU 126KB 108CSPBGA |
| 標準包裝： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 41.78MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 126KB（63K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 8K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 數據轉換器： | A/D 9x12b，D/A 4x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -10°C ~ 95°C |
| 封裝/外殼： | 108-LFBGA，CSPBGA |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁當前第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
Data Sheet
ADuC7121
Rev. B | Page 81 of 96
FIQCLR
FIQCLR is a write-only register that allows the FIQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
Use this register to disable an interrupt source only when:
The device is in the interrupt sources interrupt service
routine.
The peripheral is temporarily disabled by its own control
register.
Do not use this register to disable an FIQ source if that FIQ
source has an interrupt pending or could have an interrupt
pending.
FIQCLR Register
Name:
FIQCLR
Address:
0xFFFF010C
Default value:
0x00000000
Access:
Write only
FIQSTA
FIQSTA is a read-only register that provides the current enabled
FIQ source status (effectively a logic AND of the FIQSIG and
FIQEN bits). When set to 1, that source generates an active FIQ
request to the ARM7TDMI core. There is no priority encoder
or interrupt vector generation. This function is implemented in
software in a common interrupt handler routine.
FIQSTA Register
Name:
FIQSTA
Address:
0xFFFF0100
Default value:
0x00000000
Access:
Read only
Programmed Interrupts
Because the programmed interrupts are not maskable, they are
controlled by another register (SWICFG) that writes into both
IRQSTA and IRQSIG registers and/or the FIQSTA and FIQSIG
registers at the same time.
The 32-bit register dedicated to software interrupt is SWICFG
described in Table 111. This MMR allows the control of a
programmed source interrupt.
Table 111. SWICFG MMR Bit Designations
Bit
Description
31:3
Reserved.
2
Programmed Interrupt FIQ. Setting/clearing this bit
corresponds to setting/clearing Bit 1 of FIQSTA and
FIQSIG.
1
Programmed Interrupt IRQ1. Setting or clearing this bit
corresponds to setting or clearing Bit 1 of IRQSTA and
IRQSIG.
0
Reserved.
Any interrupt signal must be active for at least the minimum
interrupt latency time, to be detected by the interrupt controller
and to be detected by the user in the IRQSTA/FIQSTA register.
Figure 38. Interrupt Structure
Vectored Interrupt Controller (VIC)
The ADuC7121 incorporates an enhanced interrupt control
system or vectored interrupt controller. The vectored interrupt
controller for IRQ interrupt sources is enabled by setting Bit 0
of the IRQCONN register. Similarly, Bit 1 of IRQCONN enables
the vectored interrupt controller for the FIQ interrupt sources.
The vectored interrupt controller provides the following
enhancements to the standard IRQ/FIQ interrupts:
Vectored interrupts—allows a user to define separate
interrupt service routine addresses for every interrupt
source. This is achieved by using the IRQBASE and
IRQVEC registers.
IRQ/FIQ interrupts—can be nested up to eight levels
depending on the priority settings. An FIQ still has a higher
priority than an IRQ. Therefore, if the VIC is enabled for both
the FIQ and IRQ and prioritization is maximized, it is
possible to have 16 separate interrupt levels.
Programmable interrupt priorities—using the IRQP0 to
IRQP3 registers, an interrupt source can be assigned an
interrupt priority level value between 0 and 7.
09
49
2-
03
7
POINTER TO
FUNCTION
(IRQVEC)
IRQ_SOURCE
FIQ_SOURCE
PROGRAMMABLE PRIORITY
PER INTERRUPT (IRQP0/IRQP1/IRQP2)
INTERNAL
ARBITER
LOGIC
INTERRUPT VECTOR
BIT 31 TO
BIT 23
UNUSED
BIT 1 TO
BIT 0
LSB
BIT 22 TO BIT 7
(IRQBASE)
BIT 6 TO
BIT 2
HIGHEST
PRIORITY
ACTIVE IRQ
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B34-IY-F1 | CONVERTER MOD DC/DC 48V 50W |
| VI-JTZ-IX-F4 | CONVERTER MOD DC/DC 2V 30W |
| VE-B33-IY-F4 | CONVERTER MOD DC/DC 24V 50W |
| VI-JTZ-IW-F4 | CONVERTER MOD DC/DC 2V 40W |
| VJ2220Y824KBAAT4X | CAP CER 0.82UF 50V 10% X7R 2220 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7121BBCZ-RL | 功能描述:PRECISION ANALOG MCU I.C RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7122 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI? MCU |
| ADUC7122BBCZ | 功能描述:IC ARM7TDMI MCU 126KB 108CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| ADUC7122BBCZ-RL | 功能描述:PRECISION ANALOG MCU I.C RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC7124 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, Large Memory, ARM7TDMI MCU with Enhanced IRQ Handler |
發布緊急采購，3分鐘左右您將得到回復。