參數資料
型號： ADUC7121BBCZ
廠商： Analog Devices Inc
文件頁數： 64/96頁
文件大?。?/td> 0K
描述： IC ARM7TDMI MCU 126KB 108CSPBGA
標準包裝： 1
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 41.78MHz
連通性： I²C，SPI，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 126KB（63K x 16）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 9x12b，D/A 4x12b
振蕩器型： 內部
工作溫度： -10°C ~ 95°C
封裝/外殼： 108-LFBGA，CSPBGA
包裝： 托盤
ADuC7121
Data Sheet
Rev. B | Page 67 of 96
Table 96. I2CxSCTL MMR Bit Designations
Bit
Name
Description
15:11
Reserved bits.
10
I2CSTXENI
Slave transmit interrupt enable bit.
Set this bit to enable an interrupt after a slave transmits a byte.
Clear this interrupt source.
9
I2CSRXENI
Slave receive interrupt enable bit.
Set this bit to enable an interrupt after the slave receives data.
Clear this interrupt source.
8
I2CSSENI
I2C stop condition detected interrupt enable bit.
Set this bit to enable an interrupt on detecting a stop condition on the I2C bus.
Clear this interrupt source.
7
I2CNACKEN
I2C no acknowledge enable bit.
Set this bit to no acknowledge the next byte in the transmission sequence.
Clear this bit to let the hardware control the acknowledge/no acknowledge sequence.
6
I2CSSEN
I2C slave SCL stretch enable bit.
Set this bit to 1 to enable clock stretching. When SCL is low, setting this bit forces the device to hold SCL low until
I2CSSEN is cleared. If SCL is high, setting this bit forces the device to hold SCL low after the next falling edge.
Clear this bit to disable clock stretching.
5
I2CSETEN
I2C early transmit interrupt enable bit.
Setting this bit enables a transmit request interrupt just after the positive edge of SCL during the read bit
transmission.
Clear this bit to enable a transmit request interrupt just after the negative edge of SCL during the read bit
transmission.
4
I2CGCCLR
I2C general call status and ID clear bit.
Writing a 1 to this bit clears the general call status and ID bits in the I2CxSSTA register.
Clear this bit at all other times.
3
I2CHGCEN
I2C hardware general call enable. Hardware general call enable. When this bit and Bit 2 are set, and having received a
general call (Address 0x00) and a data byte, the device checks the contents of the I2CALT against the receive register.
If the contents match, the device has received a hardware general call. This is used if a device needs urgent attention
from a master device without knowing which master it needs to turn to. This is a “to whom it may concern” call. The
ADuC7121 watches for these addresses. The device that requires attention embeds its own address into the
message. All masters listen, and the one that can handle the device contacts its slave and acts appropriately. The LSB
of the I2CxALT register should always be written to 1, as per the I2C January 2000 bus specification.
Set this bit and I2CGCEN to enable hardware general call recognition in slave mode.
Clear to disable recognition of hardware general call commands.
2
I2CGCEN
I2C general call enable. Set this bit to enable the slave device to acknowledge an I2C general call, Address 0x00
(write). The device then recognizes a data bit. If it receives a 0x06 (reset and write programmable part of the slave
address by hardware) as the data byte, the I2C interface resets as per the I2C January 2000 bus specification. This
command can be used to reset an entire I2C system. If it receives a 0x04 (write programmable part of the slave
address by hardware) as the data byte, the general call interrupt status bit sets on any general call. The user must
take corrective action by reprogramming the device address.
Set this bit to allow the slave acknowledge I2C general call commands.
Clear to disable recognition of general call commands.
1
Reserved
Always set this bit to 0.
0
I2CSEN
I2C slave enable bit.
Set by the user to enable I2C slave mode.
Clear to disable I2C slave mode.
相關PDF資料
PDF描述
VE-B34-IY-F1 CONVERTER MOD DC/DC 48V 50W
VI-JTZ-IX-F4 CONVERTER MOD DC/DC 2V 30W
VE-B33-IY-F4 CONVERTER MOD DC/DC 24V 50W
VI-JTZ-IW-F4 CONVERTER MOD DC/DC 2V 40W
VJ2220Y824KBAAT4X CAP CER 0.82UF 50V 10% X7R 2220
相關代理商/技術參數
參數描述
ADUC7121BBCZ-RL 功能描述:PRECISION ANALOG MCU I.C RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7122 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI? MCU
ADUC7122BBCZ 功能描述:IC ARM7TDMI MCU 126KB 108CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
ADUC7122BBCZ-RL 功能描述:PRECISION ANALOG MCU I.C RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7124 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, Large Memory, ARM7TDMI MCU with Enhanced IRQ Handler
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*