- 您現在的位置：買賣IC網 > PDF目錄223311 > ADSP-TS203SABPZ050 (ANALOG DEVICES INC) 500 MHz TigerSHARC Processor with 4 Mbit on-chip embedded DRAM; Package: 576 ball SBGA; No of Pins: 576; Temperature Range: Ind PDF資料下載
參數資料
| 型號： | ADSP-TS203SABPZ050 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | 500 MHz TigerSHARC Processor with 4 Mbit on-chip embedded DRAM; Package: 576 ball SBGA; No of Pins: 576; Temperature Range: Ind |
| 中文描述： | 32-BIT, 125 MHz, OTHER DSP, PBGA576 |
| 封裝： | 25 X 25 MM, MS-034, BGA-576 |
| 文件頁數： | 11/48頁 |
| 文件大小： | 2017K |
| 代理商： | ADSP-TS203SABPZ050 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
ADSP-TS203S
Rev. C
|
Page 19 of 48
|
December 2006
STRAP PIN FUNCTION DESCRIPTIONS
Some pins have alternate functions at reset. Strap options set
DSP operating modes. During reset, the DSP samples the strap
option pins. Strap pins have an internal pull-up or pull-down
for the default value. If a strap pin is not connected to an over-
driving external pull-up, pull-down, or logic load, the DSP
samples the default value during reset. If strap pins are con-
nected to logic inputs, a stronger external pull-up or pull-down
may be required to ensure default value depending on leakage
and/or low level input current of the logic load. To set a mode
other than the default mode, connect the strap pin to a suffi-
ciently stronger external pull-up or pull-down. Table 16 lists
and describes each of the DSP’s strap pins.
When default configuration is used, no external resistor is
needed on the strap pins. To apply other configurations, a
500
Ω resistor connected to VDD_IO is required. If providing
external pull-downs, do not strap these pins directly to VSS; the
strap pins require 500
Ω resistor straps.
All strap pins are sampled on the rising edge of RST_IN (deas-
sertion edge). Each pin latches the strapped pin state (state of
the strap pin at the rising edge of RST_IN). Shortly after deas-
sertion of RST_IN, these pins are reconfigured to their normal
functionality.
These strap pins have an internal pull-down resistor, pull-up
resistor, or no-resistor (three-state) on each pin. The resistor
type, which is connected to the I/O pad, depends on whether
RST_IN is active (low) or if RST_IN is deasserted (high).
Table 17 shows the resistors that are enabled during active reset
and during normal operation.
Table 16. Pin Definitions—I/O Strap Pins
Signal
Type (at
Reset)
On Pin …
Description
EBOOT
I
(pd_0)
BMS
EPROM Boot.
0 = boot from EPROM immediately after reset (default)
1 = idle after reset and wait for an external device to boot DSP through the
external port or a link port
IRQEN
I
(pd)
BM
Interrupt Enable.
0 = disable and set IRQ3–0 interrupts to edge-sensitive after reset (default)
1 = enable and set IRQ3–0 interrupts to level-sensitive immediately after reset
LINK_DWIDTH
I
(pd)
TMR0E
Link Port Input Default Data Width.
0 = 1-bit (default)
1 = 4-bit
SYS_REG_WE
I
(pd_0)
BUSLOCK
SYSCON and SDRCON Write Enable.
0 = one-time writable after reset (default)
1 = always writable
TM1
I
(pu)
L1BCMPO
Test Mode 1. Do not overdrive default value during reset.
TM2
I
(pu)
TM2
Test Mode 2. Do not overdrive default value during reset.
TM3
I
(pu)
TM3
Test Mode 3. Do not overdrive default value during reset.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 21.
Table 17. Strap Pin Internal Resistors—Active Reset
(RST_IN = 0) vs. Normal Operation (RST_IN = 1)
Pin
RST_IN = 0
RST_IN = 1
BMS
(pd_0)
(pu_0)
BM
(pd)
Driven
TMR0E
(pd)
Driven
BUSLOCK
(pd_0)
(pu_0)
L1BCMPO
(pu)
Driven
TM2
(pu)
Driven
TM3
(pu)
Driven
pd = internal pull-down 5 k
Ω; pu = internal pull-up 5 kΩ;
pd_0 = internal pull-down 5 k
Ω on DSP ID = 0;
pu_0 = internal pull-up 5 k
Ω on DSP ID = 0
相關PDF資料 |
PDF描述 |
|---|---|
| ADSQ-1410-EX-C | 4-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, DMA66 |
| ADT-2734-MM-35M-02 | MALE-MALE, RF STRAIGHT ADAPTER, PLUG |
| ADT-2744-MM-HNO-02 | MALE-MALE, RF STRAIGHT ADAPTER, PLUG |
| ADT-2779-TF-SMF-00 | PANEL MOUNT, FEMALE, RF STRAIGHT ADAPTER |
| ADT-2802-7M-HNF-02 | MALE-FEMALE, RF STRAIGHT ADAPTER, JACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-TS203SBBPZ050 | 制造商:Analog Devices 功能描述:DSP - Bulk |
| ADSQ-1410 | 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
| ADSQ-1410-C | 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
| ADSQ-1410-EX-C | 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
| ADSQ-1410S | 功能描述:模數轉換器 - ADC 0 to 70C 66-pin DIP Quad 14-Bit, 10MPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。