參數資料
型號： ADE7878ACPZ
廠商： ANALOG DEVICES INC
元件分類： 模擬信號調理
英文描述： Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind
中文描述： SPECIALTY ANALOG CIRCUIT, QCC40
封裝： 6 X 6 MM, ROHS COMPLIANT, MO-220WJJD, LFCSP-40
文件頁數： 62/96頁
文件大?。?/td> 1096K
代理商： ADE7878ACPZ
ADE7854/ADE7858/ADE7868/ADE7878
Rev. E | Page 65 of 96
JUMP
TO ISR
GLOBAL
INTERRUPT
MASK
CLEAR MCU
INTERRUPT
FLAG
READ
STATUSx
JUMP
TO ISR
WRITE
BACK
STATUSx
ISR ACTION
(BASED ON STATUSx CONTENTS)
ISR RETURN
GLOBAL INTERRUPT
MASK RESET
MCU
INTERRUPT
FLAG SET
PROGRAM
SEQUENCE
t1
t2
t3
IRQx
0
85
10
-0
57
Figure 79. Interrupt Management
JUMP
TO ISR
GLOBAL
INTERRUPT
MASK
CLEAR MCU
INTERRUPT
FLAG
READ
STATUSx
READ
PHx
JUMP
TO ISR
WRITE
BACK
STATUSx
ISR ACTION
(BASED ON STATUSx CONTENTS)
ISR RETURN
GLOBAL INTERRUPT
MASK RESET
MCU
INTERRUPT
FLAG SET
PROGRAM
SEQUENCE
t1
t2
t3
IRQx
08
51
0-
0
58
Figure 80. Interrupt Management when PHSTATUS, IPEAK, VPEAK, or PHSIGN Registers are Involved
status register is read immediately to identify the phase that
triggered the interrupt. The name, PHx, in Figure 80 denotes
one of the PHSTATUS, IPEAK, VPEAK, or PHSIGN registers.
Then, STATUSx is written back to clear the status flag(s).
SERIAL INTERFACES
The ADE7854/ADE7858/ADE7868/ADE7878 have three serial
port interfaces: one fully licensed I2C interface, one serial
peripheral interface (SPI), and one high speed data capture port
(HSDC). As the SPI pins are multiplexed with some of the pins
of the I2C and HSDC ports, the ADE78xx accepts two confi-
gurations: one using the SPI port only and one using the I2C
port in conjunction with the HSDC port.
Serial Interface Choice
After reset, the HSDC port is always disabled. Choose between
the I2C and SPI ports by manipulating the SS/HSA pin after
power-up or after a hardware reset. If the SS/HSA pin is kept
high, then the ADE7854/ADE7858/ADE7868/ADE7878 use the
I2C port until a new hardware reset is executed. If the SS/HSA
pin is toggled high to low three times after power-up or after a
hardware reset, the ADE7854/ADE7858/ADE7868/ADE7878
use the SPI port until a new hardware reset is executed. This
manipulation of the SS/HSA pin can be accomplished in two
ways. First, use the SS/HSA pin of the master device (that is, the
microcontroller) as a regular I/O pin and toggle it three times.
Second, execute three SPI write operations to a location in the
address space that is not allocated to a specific ADE78xx register
(for example 0xEBFF, where eight bit writes can be executed).
These writes allow the SS/HSA pin to toggle three times. See the
section for details on the write protocol
involved.
After the serial port choice is completed, it needs to be locked.
Consequently, the active port remains in use until a hardware
reset is executed in PSM0 normal mode or until a power-down.
If I2C is the active serial port, Bit 1 (I2C_LOCK) of the CONFIG2
register must be set to 1 to lock it in. From this moment, the
ADE7854/ADE7858/ADE7868/ADE7878 ignore spurious
toggling of the SS pin and an eventual switch into using the SPI
port is no longer possible. If the SPI is the active serial port, any
write to the CONFIG2 register locks the port. From this moment,
a switch into using the I2C port is no longer possible. Once locked,
the serial port choice is maintained when the ADE78xx changes
PSMx power modes.
The functionality of the ADE78xx is accessible via several on-
chip registers. The contents of these registers can be updated or
read using either the I2C or SPI interfaces. The HSDC port provides
the state of up to 16 registers representing instantaneous values of
phase voltages and neutral currents, and active, reactive, and
apparent powers.
I2C-Compatible Interface
The ADE7854/ADE7858/ADE7868/ADE7878 supports a fully
licensed I2C interface. The I2C interface is implemented as a full
hardware slave. SDA is the data I/O pin, and SCL is the serial
clock. These two pins are shared with the MOSI and SCLK pins
of the on-chip SPI interface. The maximum serial clock frequency
supported by this interface is 400 kHz.
The two pins used for data transfer, SDA and SCL, are confi-
gured in a wire-AND’ed format that allows arbitration in a
multimaster system.
The transfer sequence of an I2C system consists of a master device
initiating a transfer by generating a start condition while the bus
is idle. The master transmits the address of the slave device and
the direction of the data transfer in the initial address transfer. If
the slave acknowledges, the data transfer is initiated. This con-
tinues until the master issues a stop condition, and the bus
becomes idle.
相關PDF資料
PDF描述
ADE7878ACPZ-RL Poly Phase Multifunction Energy Metering IC With Total And Fundamental Powers, No Of Pins: 40, Temperature Range: Ind
ADG529FTQ 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, CDIP18
ADJ24006 POWER/SIGNAL RELAY, SPST, LATCHED, 0.042A (COIL), 6VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT
ADJ24012 POWER/SIGNAL RELAY, SPST, LATCHED, 0.021A (COIL), 12VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT
ADJ24024 POWER/SIGNAL RELAY, SPST, LATCHED, 0.01A (COIL), 24VDC (COIL), 250mW (COIL), THROUGH HOLE-STRAIGHT MOUNT
相關代理商/技術參數
參數描述
ADE7878ACPZ 制造商:Analog Devices 功能描述:IC MULTIFUNCTION ENERGY METERING LFCSP40
ADE7878ACPZ-RL 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7878XCPZ 制造商:Analog Devices 功能描述:POLY PHASE MULTIFUNCTION ENERGY METERING IC WITH TOTAL - Bulk
ADE7880 制造商:Analog Devices 功能描述:BOARD EVAL ENERGY METER ADE
ADE7880ACPZ 功能描述:IC ENERGY METERING 3PH 40LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*