- 您現在的位置：買賣IC網 > PDF目錄1895 > AD9979BCPZRL (Analog Devices Inc)IC PROCESSOR CCD 14BIT 48-LFCSP PDF資料下載
參數資料
| 型號： | AD9979BCPZRL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 31/56頁 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR CCD 14BIT 48-LFCSP |
| 標準包裝： | 1 |
| 類型： | CCD 信號處理器，14 位 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 3 線串口 |
| 電流 - 電源： | 48mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 標準包裝 |
| 其它名稱： | AD9979BCPZRLDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
AD9979
Rev. C | Page 37 of 56
VD
HD
CLI
XX
X
tHDCLI
XX
X
tCLISHP
tCLIDLY
0
12
NOTES
1. EXTERNAL HD FALLING EDGE IS LATCHED BY CLI RISING EDGE, THEN LATCHED AGAIN BY SHPLOC (INTERNAL SAMPLING EDGE).
2. INTERNAL H-COUNTER IS ALWAYS RESET 11.5 CLOCK CYCLES AFTER THE INTERNAL HD FALLING EDGE, AT SHDLOC (INTERNAL SAMPLING EDGE).
3. DEPENDING ON THE VALUE OF SHDLOC, H-COUNTER RESET CAN OCCUR 13 OR 14 CLI CLOCK EDGES AFTER THE EXTERNAL HD FALLING EDGE.
4. SHPLOC = 32, SHDLOC = 0 IS SHOWN IN ABOVE EXAMPLE. IN THIS CASE, THE H-COUNTER RESET OCCURS 13 CLI RISING EDGES AFTER HD FALLING EDGE.
5. HD FALLING EDGE MUST OCCUR COINCIDENT WITH VD FALLING EDGE (WITHIN SAME CLI CYCLE) OR AFTER VD FALLING EDGE. HD FALLING
EDGE MUST NOT OCCUR WITHIN 1 CLI CYCLES IMMEDIATELY BEFORE VD FALLING EDGE.
H-COUNTER
RESET
SHDLOC
INTERNAL
HD
INTERNAL
H-COUNTER
(PIXEL COUNTER)
tVDHD
11.5 CYCLES
SHPLOC
INTERNAL
05
95
7-
0
55
Figure 53. Horizontal Counter Pipeline Delay
Additional Restrictions
When operating, note the following restrictions:
The HD falling edge should be located in the same CLI
clock cycle as the VD falling edge or later than the VD
falling edge. The HD falling edge should not be located
within 1 cycle prior to the VD falling edge.
If possible, perform all start-up serial writes with VD and
HD disabled. This prevents unknown behavior caused by
partial updating of registers before all information is loaded.
The internal horizontal counter is reset 12 CLI cycles after the
falling edge of HD. See Figure 53 for details on how the internal
counter is reset.
STANDBY MODE OPERATION
The AD9979 contains two different standby modes to optimize
the overall power dissipation in a particular application. Bits[1:0]
of Address 0x00 control the power-down state of the device.
STANDBY[1:0] = 00 = normal operation (full power)
STANDBY[1:0] = 01 = reference standby mode
STANDBY[1:0] = 10 or 11 = total shut-down mode
(lowest power)
Table 22 summarizes the operation of each power-down mode.
OUT_CONTROL (Address 0x11, Bit [0]) takes priority over the
reference standby mode in determining the digital output states,
but total shutdown mode takes priority over OUT_CONTROL.
Total shutdown mode has the lowest power consumption. When
returning from total shutdown mode to normal operation, the
timing core must be reset at least 100 μs after STANDBY
(Address 0x00, Bits[1:0]) is written to.
There is an additional register to independently disable the
internal voltage reference buffer, REFBUF_PWRDN (Bit 2,
(Address 0x00). By default, the buffer is disabled. It must be
enabled for normal operation.
CLI FREQUENCY CHANGE
If the input clock (CLI) is interrupted or changes to a different
frequency, the timing core must be reset for proper operation. After
the CLI clock has settled to the new frequency, or the previous
frequency is resumed, write 0 and then 1 to TGCORE_RST
(Address 0x14). This guarantees proper timing core operation.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9980KSTZ-95 | IC INTERFACE 8BIT ANALOG 80LQFP |
| AD9981KSTZ-95 | IC INTERFACE 10BIT ANALOG 80LQFP |
| AD9983AKSTZ-170 | IC DISPLAY 8BIT 170MSPS 80LQFP |
| AD9985KSTZ-140 | IC INTERFACE 8BIT 140MSPS 80LQFP |
| AD9990BBCZ | IC CCD SGNL PROCESSOR 112CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9980 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9980/PCBZ | 功能描述:KIT EVALUATION AD9980 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| AD9980KSTZ-80 | 功能描述:IC INTERFACE 8BIT ANALOG 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9980KSTZ-95 | 功能描述:IC INTERFACE 8BIT ANALOG 80LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1 |
| AD9980KSTZ-RL95 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。