- 您現在的位置：買賣IC網 > PDF目錄16822 > AD9959/PCBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9959 PDF資料下載
參數資料
| 型號： | AD9959/PCBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/44頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9959 |
| 產品培訓模塊： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 設計資源： | Phase Coherent FSK Modulator (CN0186) AD9958/59 Eval Brd Schematics AD9958/59 Eval Brd Gerber Files AD9959 Eval Brd BOM |
| 標準包裝： | 1 |
| 主要目的： | 計時，直接數字合成（DDS） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9959 |
| 主要屬性： | 10 位數模轉換器，32 位調節字寬 |
| 次要屬性： | 4 通道 |
| 已供物品： | 板，線纜，軟件 |
| 其它名稱： | AD9959/PCB AD9959/PCB-ND Q2548077 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9959
Rev. B | Page 10 of 44
Pin No.
Mnemonic
Description
24
CLK_MODE_SEL
I
Control Pin for the Oscillator Section. Caution: Do not drive this pin beyond 1.8 V.
When high (1.8 V), the oscillator section is enabled to accept a crystal as the
REF_CLK source. When low, the oscillator section is bypassed.
27
LOOP_FILTER
I
Connects to the external zero compensation network of the PLL loop filter.
Typically, the network consists of a 0 Ω resistor in series with a 680 pF capacitor
tied to AVDD.
29
CH0_IOUT
O
Complementary DAC Output. Terminates into AVDD.
30
CH0_IOUT
O
True DAC Output. Terminates into AVDD.
35
CH1_IOUT
O
Complementary DAC Output. Terminates into AVDD.
36
CH1_IOUT
O
True DAC Output. Terminates into AVDD.
40 to 43
P0 to P3
I
Data pins used for modulation (FSK, PSK, ASK), to start/stop the sweep accumulators
or used to ramp up/ramp down the output amplitude. The data is synchronous to
the SYNC_CLK (Pin 54). The data inputs must meet the setup and hold time
requirements of the SYNC_CLK. The functionality of these pins is controlled by the
profile pin configuration (PPC) bits (FR1[14:12]).
46
I/O_UPDATE
I
A rising edge transfers data from the serial I/O port buffer to active registers.
I/O_UPDATE is synchronous to the SYNC_CLK (Pin 54). I/O_UPDATE must meet the
setup and hold time requirements of the SYNC_CLK to guarantee a fixed pipeline
delay of data to the DAC output; otherwise, a ±1 SYNC_CLK period of pipeline
uncertainty exists. The minimum pulse width is one SYNC_CLK period.
47
CS
I
Active Low Chip Select. Allows multiple devices to share a common I/O bus (SPI).
48
SCLK
I
Serial Data Clock for I/O Operations. Data bits are written on the rising edge of
SCLK and read on the falling edge of SCLK.
49
DVDD_I/O
I
3.3 V Digital Power Supply for SPI Port and Digital I/O.
50
SDIO_0
I/O
Data Pin SDIO_0 is dedicated to the serial port I/O only.
51, 52
SDIO_1, SDIO_2
I/O
Data Pin SDIO_1 and Data Pin SDIO_2 can be used for the serial I/O port or used to
initiate a ramp-up/ramp-down (RU/RD) of the DAC output amplitude.
53
SDIO_3
I/O
Data Pin SDIO_3 can be used for the serial I/O port or to initiate a ramp-up/ramp-down
(RU/RD) of the DAC output amplitude. In single-bit or 2-bit modes, SDIO_3 is used
for SYNC_I/O. If the SYNC_I/O function is not used, tie to ground or Logic 0. Do not
let SDIO_3 float in single-bit or 2-bit modes.
54
SYNC_CLK
O
The SYNC_CLK runs at one-fourth the system clock rate; it can be disabled. I/O_UPDATE
or data (Pin 40 to Pin 43) is synchronous to the SYNC_CLK. To guarantee a fixed pipeline
delay of data to DAC output, I/O_UPDATE or data (Pin 40 to Pin 43) must meet the
setup and hold time requirements to the rising edge of SYNC_CLK; otherwise, a ±1
SYNC_CLK period of uncertainty occurs.
1 I = input, O = output.
相關PDF資料 |
PDF描述 |
|---|---|
| ECM12DTKT-S288 | CONN EDGECARD 24POS .156 EXTEND |
| ATWEBDVK-02RC | KIT DEV TCP/IP AT89C51RD2 REMOTE |
| KSZ8862-10FL-EVAL | BOARD EVALUATION KSZ8862-10FL |
| ITCSN-0800-25-U | HEATSHRINK ITCSN 4/5" X 25' |
| ECM15DCTT-S288 | CONN EDGECARD 30POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD995PCBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:1 GSPS Quadrature Digital Upconverter w/18-Bit IQ Data Path and 14-Bit DAC |
| AD9960BSTZ | 功能描述:RFID應答器 MxFE for RFID Reader Transceiver RoHS:否 制造商:Murata 存儲容量:512 bit 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| AD9960BSTZRL | 功能描述:IC MXFE FOR RFID READER/TXRX RoHS:是 類別:RF/IF 和 RFID >> RFID IC 系列:AD9960B 其它有關文件:CR14 View All Specifications 標準包裝:1 系列:- RF 型:收發器 頻率:13.56MHz 特點:ISO14443-B 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SO 包裝:Digi-Reel® 其它名稱:497-5719-6 |
| AD9960XSTZ | 制造商:Analog Devices 功能描述:SINGLE-SUPPLY CABLE MODEM/SET-TOP BOX MIXED-SIGNAL FRONT END - Trays |
| AD9961 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-/12-Bit, Low Power, Broadband MxFE |
發布緊急采購，3分鐘左右您將得到回復。