- 您現在的位置：買賣IC網 > PDF目錄1894 > AD9923ABBCZ (Analog Devices Inc)IC PROCESSOR CCD 12BIT 105CSPBGA PDF資料下載
參數資料
| 型號： | AD9923ABBCZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 43/84頁 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR CCD 12BIT 105CSPBGA |
| 標準包裝： | 1 |
| 類型： | CCD 信號處理器，12 位 |
| 輸入類型： | 邏輯 |
| 輸出類型： | 邏輯 |
| 接口： | 3 線串口 |
| 電流 - 電源： | 20mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 105-LFBGA，CSPBGA |
| 供應商設備封裝： | 105-CSPBGA（8x8） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
AD9923A
Rev. A | Page 48 of 84
Table 39. SUBCK and TRIGGER Register Parameters
Register
Length
(Bits)
Range
Description
TRIGGER
8
On/off for eight signals
0: triggers SHUT0 signal.
1: triggers SHUT1 signal.
2: triggers SHUT2 signal.
3: triggers SHUT3 signal.
4: triggers VSUB0 signal.
5: triggers VSUB1 signal.
6: triggers EXPOSURE operation.
7: triggers READOUT operation.
READOUTNUM
3
0 to 7 fields
Number of fields to suppress SUBCK after exposure.
EXPOSURENUM
12
0 to 4095 fields
Number of fields to suppress to SUBCK and VSG during exposure time (low
speed shutter).
VDHDOFF
1
On/off
Disable VD/HD output during exposure.
1 = disable VD.
0 = enable VD.
SUBCKPOL1
1
High/low
SUBCK start polarity for SUBCK1 and SUBCK2.
SUBCK1TOG11
12
0 to 4095 pixel locations
First toggle positions for first SUBCK pulse (normal shutter).
SUBCK1TOG21
12
0 to 4095 pixel locations
Second toggle positions for first SUBCK pulse (normal shutter).
SUBCK2TOG11
12
0 to 4095 pixel locations
First toggle positions for second SUBCK pulse in last line (high precision).
SUBCK2TOG21
12
0 to 4095 pixel locations
Second toggle positions for second SUBCK pulse in last line (high precision).
12
1 to 4095 pulses
Total number of SUBCKs per field, at one pulse per line.
12
0 to 4095 pulses
Number of pulses, after the VSG line, to suppress SUBCK.
SUBCKMASK1
2
0 to 3 masking mode
Additional masking of SUBCK output.
0 = no additional mask.
1 = start mask at VD edge.
2 = use internal SHUT3 signal to mask.
1 Register is not VD updated but updated at the start of the line after the sensor gate line.
Shutter Outputs
The AD9923A contains three shutter output pins: VSUB,
MSHUT, and STROBE. Internally, there are six possible shutter
signals available: VSUB0, VSUB1, SHUT0, SHUT1, SHUT2,
and SHUT3. Any of these signals, and the following combinations:
SHUT0 ^ VSUB0, SHUT0 ^ VSUB1, SHUT0 ^ SHUT1,
SHUT0 ^ SHUT2, can be mapped to any of the output pins
using the VSUB_CTRL, MSHUT_CTRL, and STROBE_CTRL
registers.
The VSUB signals behave differently than the SHUT signals,
and are generally used for the VSUB output pin. If a more generic
approach is desired for the shutter signals, the SHUT signals can
be used for the VSUB output pin.
It is also possible to configure the SYNC pin as an output and
send one of the internal shutter signals, or the combinations listed
above, to the SYNC pin using the TESTO_CTRL register
function. This provides the flexibility of outputting up to four
shutter outputs if the external SYNC input function is not needed.
VSUB Signal Operation
The CCD readout bias (VSUB) can be programmed to accom-
modate different CCDs. Figure 67 shows two available modes.
In Mode 0, VSUB goes active when the exposure begins during
the field of the last SUBCK. The on position (rising edge in
Figure 67) is programmable to any line within the field. VSUB
remains active until the end of the image readout. In Mode 1,
the VSUB is not activated until the start of the readout.
A function called VSUB_KEEPON is also available. When the
appropriate VSUB_KEEPON bit is set high, the VSUB output
remains active, even after the readout has finished. To disable
the VSUB at a later time, return this bit to low.
The AD9923A contains two programmable VSUB signals,
VSUB0 and VSUB1. Either of these signals can be mapped to
the VSUB output pin, the MSHUT pin, or the STROBE pin.
SHUT Signal Operation
相關PDF資料 |
PDF描述 |
|---|---|
| AD9942BBCZ | IC PROCESSOR SGNL 14B 100CSPBGA |
| AD9944KCPZRL | IC CCD SIGNAL PROCESSOR 32-LFCSP |
| AD9945KCPZRL7 | IC CCD SIGNAL PROCESSOR 32-LFCSP |
| AD9948KCPZ | IC CCD SIGNAL PROCESSOR 40-LFCSP |
| AD9949KCPZ | IC CCD SIGNAL PROCESSOR 40-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9923ABBCZRL | 功能描述:IC PROCESSOR CCD 12BIT 105CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9923BBCZ | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
| AD9923BBCZRL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9924BBCZ | 制造商:Analog Devices 功能描述: |
| AD9924BBCZRL | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。