參數資料
型號： 935270523557
廠商： NXP SEMICONDUCTORS
元件分類： 總線控制器
英文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封裝： 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-414-1, LQFP-64
文件頁數： 53/93頁
文件大?。?/td> 2118K
代理商： 935270523557
Philips Semiconductors
ISP1160
Embedded USB Host Controller
Product data
Rev. 03 — 27 February 2003
57 of 89
9397 750 10765
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Code (Hex): [1] = 15, [2] = 16 — read
Code (Hex): [1] = 95, [2] = 96 — write
2
PSS
(read) PortSuspendStatus: This bit indicates whether the port is
suspended or in the resume sequence. It is set by a
SetSuspendState write and cleared when
PortSuspendStatusChange is set at the end of the resume
interval. This bit cannot be set if CurrentConnectStatus is cleared.
This bit is also cleared when PortResetStatusChange is set at the
end of the port reset or when the HC is placed in the
USBRESUME state. If an upstream resume is in progress, it
should propagate to the HC.
0 — port is not suspended
1 — port is suspended
(write) SetPortSuspend: The HCD sets the PortSuspendStatus
bit by writing a logic 1 to this bit. Writing a logic 0 has no effect. If
CurrentConnectStatus is cleared, this write does not set
PortSuspendStatus; instead it sets ConnectStatusChange. This
informs the driver that it attempted to suspend a disconnected
port.
1
PES
(read) PortEnableStatus: This bit indicates whether the port is
enabled or disabled. The Root Hub may clear this bit when an
overcurrent condition, disconnect event, switched-off power, or
operational bus error such as babble is detected. This change also
causes PortEnabledStatusChange to be set. The HCD sets this bit
by writing SetPortEnable and clears it by writing ClearPortEnable.
This bit cannot be set when CurrentConnectStatus is cleared. This
bit is also set, if it is not already, at the completion of a port reset
when ResetStatusChange is set or port suspend when
SuspendStatusChange is set.
0 — port is disabled
1 — port is enabled
(write) SetPortEnable: The HCD sets PortEnableStatus by writing
a logic 1. Writing a logic 0 has no effect. If CurrentConnectStatus
is cleared, this write does not set PortEnableStatus, but instead
sets ConnectStatusChange. This informs the driver that it
attempted to enable a disconnected port.
0
CCS
(read) CurrentConnectStatus: This bit reects the current state
of the downstream port.
0 — no device connected
1 — device connected
(write) ClearPortEnable: The HCD writes a logic 1 to this bit to
clear the PortEnableStatus bit. Writing a logic 0 has no effect.
CurrentConnectStatus is not affected by any write.
Remark: This bit always reads logic 1 when the attached device is
nonremovable (DeviceRemoveable[NDP]).
Table 35:
HcRshPortStatus[1:2] register: bit description…continued
Bit
Symbol
Description
相關PDF資料
PDF描述
935270668112 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PDSO48
935272535118 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA56
935272535157 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PBGA56
935268661112 POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PDSO48
935270671112 CBT/FST/QS/5C/B SERIES, QUAD 1-BIT DRIVER, TRUE OUTPUT, PDSO14
相關代理商/技術參數
參數描述
935270713557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP
935270792551 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270792557 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA
935270793551 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
935270793557 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*