
XRT86L30
SINGLE T1/E1/J1 FRAMER/LIU COMBO
REV. P1.0.1
PRELIMINARY
211
10.3 B
RIEF
D
ISCUSSION
OF
C
OMMON
C
HANNEL
S
IGNALING
IN
E1 F
RAMING
F
ORMAT
As the name referred, Common Channel Signaling is signaling information common to all thirty voice or data
channels of an E1 trunk. Time slot 16 may be used to carry Common Channel Signaling data of up to a rate of
64kbits/s. The national bits of time slot 0 may also be used for Common Channel Signaling. Since there are
five national bits of time slot 0 per every two E1 frames, the total bandwidth of the national bits is 20kbits/s. The
Common Channel Signaling is essentially data link information that provides performance monitoring and a
transmission quality report.
10.4 B
RIEF
D
ISCUSSION
OF
C
HANNEL
A
SSOCIATED
S
IGNALING
IN
E1 F
RAMING
F
ORMAT
Signaling is required when dealing with voice and dial-up data services in E1 applications. Traditionally, signal-
ing is provided on a dial-up telephone line across the talk-path. Signaling is used to tell the receiver where the
call or route is destined. The signal is sent through switches along the route to a distant end. Common types
of signals are:
On hook
Off hook
Dial tone
Dialed digits
Ringing cycle
Busy tone
A signal is consists of four bits namely A, B, C and D. These bits define the state of the call for a particular time
slot. Time slot 16 of each E1 frame can carry CAS signals for two E1 voice or data channels. Therefore, six-
teen E1 frames are needed to carry CAS signals for all 32 E1 channels. The sixteen E1 frames then forms a
CAS Multi-frame.
10.5 I
NSERT
/E
XTRACT
S
IGNALING
B
ITS
FROM
TSCR R
EGISTER
The four most significant bits of the Transmit Signaling Control Register (TSCR) of each time slot can be used
to store outgoing signaling data. The user can program these bits through microprocessor access. If the
XRT86L30 framer is configure to insert signaling bits from TSCR registers, the E1 Transmit Framer block will
fill up the time slot 16 octet with the signaling bits stored inside the TSCR registers. The insertion of signaling
bit into PCM data is done on a per-channel basis. The most significant bit (Bit 7) of TSCR register is used to
store Signaling bit A. Bit 6 is used to hold Signaling bit B. Bit 5 is used to hold Signaling bit C. Bit 4 is used to
hold Signaling bit D.
10.6 I
NSERT
/E
XTRACT
S
IGNALING
B
ITS
FROM
T
X
CHN[0]_
N
/T
X
SIG P
IN
The XRT86L30 framer can be configured to insert/extract signaling bits provided by external equipment
through the external signaling bus. When the Fractional E1 mode is enabled, this bus is configured as TxSIG
and RxSIG. These pins act as an the signaling bus for the outbound E1 frames.
Figure 77 shows a timing diagram of the TxSIG input pin. Figure 78 shows a timing diagram of the RxSIG out-
put pin. Please note that the Signaling Bit A of a certain channel coincides with Bit 5 of the PCM data of that
channel; Signaling Bit B coincides with Bit 6 of the PCM data; Signaling Bit C coincides with Bit 7 of the PCM
data and Signaling Bit D coincides with Bit 8 (LSB) of the PCM data.
F
IGURE
77. T
IMING
D
IAGRAM
OF
THE
T
X
SIG I
NPUT