參數資料
型號： XRT83L34
廠商： Exar Corporation
英文描述： QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
中文描述： 四T1/E1/J1收發左/上海收發器和時鐘恢復和抖動衰減器
文件頁數： 66/82頁
文件大?。?/td> 447K
代理商： XRT83L34
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
PRELIMINARY
REV. P1.3.4
63
CLOCK SELECT REGISTER
The input clock source is used to generate all the necessary clock references internally to the LIU. The
microprocessor timing is derived from a PLL output which is chosen by programming the Clock Select Bits and
the Master Clock Rate in register 0x41h. Therefore, if the clock selection bits or the MCLRATE bit are being
programmed, the frequency of the PLL output will be adjusted accordingly. During this adjustment, it is
important to "Not" write to any other bit location within the same register while selecting the input/output clock
frequency. For best results, when bits D[6:3] are being changed, the other bits D[7] and D[2:0] as shown in
Figure 25. should retain their previous values.
F
IGURE
25. R
EGISTER
0
X
81
H
S
UB
R
EGISTERS
Programming Examples:
Example 1: Changing bits D[6:3]
If bits D[6:3] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 2: Changing bits D[7] and D[2:0]
If bits D[7] and D[2:0] are the only values within the register that will change in a WRITE process, the
microprocessor only needs to initiate ONE write operation.
Example 3: Changing bits within D[6:3] and the other bits
In this scenario, one must initiate TWO write operations such that bits D[6:3] and the other bits do not change
within ONE write cycle. It is recommended that bits D[6:0] and the other bits be treated as two independent
sub-registers. One can either change the clock selection bits and then change bits D[7] and D[2:0] on the
SECOND write, or vice-versa. No order or sequence is necessary.
D0
D1
D2
D3
D4
D5
D6
D7
Clock Selection Bits
ExLOS, ICT
E1arben
相關PDF資料
PDF描述
XRT83L34IV QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SH314 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH314_0610 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH314IB 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH38 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
相關代理商/技術參數
參數描述
XRT83L34_05 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L34ES 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83L34IV 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT83L34IV-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT83L34IVTR 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*