參數資料
型號： XRT83L34
廠商： Exar Corporation
英文描述： QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
中文描述： 四T1/E1/J1收發左/上海收發器和時鐘恢復和抖動衰減器
文件頁數： 28/82頁
文件大?。?/td> 447K
代理商： XRT83L34
XRT83L34
QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
PRELIMINARY
REV. P1.3.4
25
ARBITRARY PULSE GENERATOR FOR T1 AND E1
The arbitrary pulse generator divides the pulse into eight individual segments. Each segment is set by a 7-Bit
binary word by programming the appropriate channel register. This allows the system designer to set the
overshoot, amplitude, and undershoot for a unique line build out. The MSB (bit 7) is a sign-bit. If the sign-bit is
set to “1”, the segment will move in a positive direction relative to a flat line (zero) condition. If this sign-bit is set
to “0”, the segment will move in a negative direction relative to a flat line condition. A pulse with numbered
segments is shown in Figure 11.
N
OTE
:
By default, the arbitrary segments are programmed to 0x00h. The transmitter outputs will result in an all zero pattern
to the line.
TRANSMITTER
DIGITAL DATA FORMAT
Both the transmitter and receiver can be configured to operate in dual or single-rail data formats. This feature
is available under both
Hardware
and
Host
control modes, on a global basis. The dual or single-rail data
format is determined by the state of the SR/DR pin in
Hardware
mode or SR/DR interface bit in the
Host
mode. In single-rail mode, transmit clock and NRZ data are applied to TCLK_n and TPOS_n/TDATA_n pins
respectively. In single-rail and
Hardware
mode the TNEG_n/CODES_n input can be used as the CODES
function. With TNEG_n/CODES_n tied “Low”, HDB3 or B8ZS encoding and decoding are enabled for E1 and
T1 modes respectively. With TNEG_n/CODES_n tied “High”, the AMI coding scheme is selected. In both dual
or single-rail modes of operations, the transmitter converts digital input data to a bipolar format before being
transmitted to the line.
TRANSMIT CLOCK (TCLK) SAMPLING EDGE
Serial transmit data at TPOS_n/TDATA_n and TNEG_n/CODES_n are clocked into the XRT83L34 under the
synchronization of TCLK_n. With a “0” written to the TCLKE interface bit, or by pulling the TCLKE pin “Low”,
input data is sampled on the falling edge of TCLK_n. The sampling edge is inverted with a “1” written to TCLKE
interface bit, or by connecting the TCLKE pin “High”.
F
IGURE
11. A
RBITRARY
P
ULSE
S
EGMENT
A
SSIGNMENT
1
2
3
4
5
6
7
8
Segment
Register
1
2
3
4
5
6
7
8
0xn8
0xn9
0xna
0xnb
0xnc
0xnd
0xne
0xnf
相關PDF資料
PDF描述
XRT83L34IV QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SH314 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH314_0610 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH314IB 14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SH38 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
相關代理商/技術參數
參數描述
XRT83L34_05 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83L34ES 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83L34IV 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT83L34IV-F 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
XRT83L34IVTR 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*