參數資料
型號： XR16C872
廠商： Exar Corporation
英文描述： Dual UART with 1284 Parallel Port and Plug-and-Play（PnP） Controller(雙通用異步接收器/發送器（帶1284雙向并行端口和即插即用控制器）)
中文描述： 雙UART）與1284并行端口，插頭插即用（PnP）功能控制器（雙通用異步接收器/發送器（帶1284雙向并行端口和即插即用控制器）
文件頁數： 37/60頁
文件大?。?/td> 314K
代理商： XR16C872
XR16C872
37
Rev. P1.00
Preliminary
is unloaded to the lower limit of the hysteresis. The
state of this register bit changes with the status of the
hardware flow control. RTS# functions normally when
hardware flow control is disabled.
0 = Automatic RTS flow control is disabled. (normal
default condition)
1 = Enable Automatic RTS flow control.
EFR bit-7:
Automatic CTS Flow Control.
Logic 0 = Automatic CTS flow control is disabled.
(normal default condition)
Logic 1 = Enable Automatic CTS flow control. Trans-
mission stops when CTS# goes to a logical 1. Trans-
mission resumes when the CTS# pin returns to a
logical 0.
FEATURE CONTROL REGISTER (FCR)
This register is only accessible when LCR is set to
0xBF.
FCTR BIT 0-1:
User selectable RTS# delay or hysteresis for hardware
flow control application. After reset, these bits are set
to logic 0 to select the next trigger level on the RX FIFO
trigger level (FCR bit 6-7,Table-A). These bits are also
associated with EMSR bit-4 and 5 for the hysteresis
control. See EMSR register for more details.
FCTR BIT-2:
0 = Select RX input as encoded IrDa data.
1 = Select RX input as active high encoded IrDa data.
FCTR BIT-3:
Auto RS485 Half Duplex Direction control.
*OP1# output is not available in the 872, however, it
does change the behavior of the transmit empty inter-
rupt.
0 = Transmitter generates an interrupt when transmit
holding register becomes empty while transmit shift
register is still shifting data out.
1 = Enable Auto RS485 Half Duplex Direction Control.
The transmit empty interrupt generation is delayed
until the Transmitter Shift Register (TSR) becomes
empty.
FCTR BIT 4-5:
Transmit / receive trigger table select.
FCTR
Bit-5
0
0
1
1
FCTR
Bit-4
0
1
0
1
Trigger
Table
Table-A (TX/RX)
Table-B (TX/RX)
Table-C (TX/RX)
Table-D (TX/RX)
FCTR BIT-6:
Scratch Pad Register (SPR) or EMSR select.
0 = Scratch Pad Register (SPR) is selected as general
read and write register. 16C550 compatible mode.
1 = FIFO count register, Enhanced Mode Select
Register (EMSR). Number of characters in transmit or
receive holding register can be read via Scratch Pad
Register when this bit is set. Enhanced Mode is
selected when it is written into it.
FCTR BIT-7:
Programmable trigger register select.
0 = Receiver programmable trigger level register (TRG)
is selected.
1 = Transmitter programmable trigger level register
(TRG) is selected.
相關PDF資料
PDF描述
XR16L2450 2.25V TO 5.5V DUART
XR16L2450IJ 97-3108A20-29S-KIT
XR16L2450IM 2.25V TO 5.5V DUART
XR16L2550IJ LOW VOLTAGE DUART WITH 16-BYTE FIFO
XR16L2550IL LOW VOLTAGE DUART WITH 16-BYTE FIFO
相關代理商/技術參數
參數描述
XR16C872CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16C872IQ 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16L2450 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
XR16L2450_05 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
XR16L2450IJ 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*