參數資料
型號： W29GL064CT9A
廠商： WINBOND ELECTRONICS CORP
元件分類： PROM
英文描述： 64M X 1 FLASH 3V PROM, 100 ns, PBGA48
封裝： GREEN, VFBGA-48
文件頁數： 5/64頁
文件大小： 563K
代理商： W29GL064CT9A
W29GL064C
Publication Release Date: September 8, 2010
7
Preliminary - Revision A
7.2.3
Device Reset Operation
Pulling the #RESET pin Low for a period equal to or greater than tRP will return the device to Read
mode. If the device is performing a program or erase operation, the reset operation will take at most a
period of tREADY1 before the device returns to Read mode. The RY/#BY pin will remain Low (Busy
Status) until the device returns to Read mode.
Note, the device draws larger current if the #RESET pin is held at voltages greater that GND+0.3V
and less than or equal to VIL. When the #RESET pin is held a GND±0.3V, the device only consumes
Reset (ICC5) current.
It is recommended to tie the system reset signal to the #RESET pin of the flash memory. This allows
the device to be reset with the system and puts it in a state where the system can immediately begin
reading boot code from it.
Executing the Reset instruction will reset the device back to the Read mode in the following situations:
During an erase instruction sequence, before the full instruction set is completed.
Sector erase time-out period
Erase failed, while DQ5 is High.
During program instruction sequence, before the full instruction set is completed, including the
erase-suspended program instruction.
Program failed, while DQ5 is High as well as the erase-suspended program failure.
Auto-select mode
CFI mode
The user must issue a reset instruction to reset the device back to the Read mode when the
device is in Auto-Select mode or CFI mode, or when there is a program or erase failure (DQ5
is High).
When the device is performing a Programming (not program fail) or Erasing (Not erase fail)
function, the device will ignore reset commands.
7.2.4
Standby Mode
Standby mode is entered when both #RESET and #CE are driven to VCC ±300mV (inactive state).
(Note, if both pins are not within the EVIO ±0.3V, but at VIH, standby current will be greater.) At this
time output pins are placed in the high impedance state regardless of the state of the #WE or #OE
pins and the device will draw minimal standby current (ICC4). If the device is deselected during erase
or program operation, the device will draw active current until the operation is completed.
7.2.5
Output Disable Mode
The #OE pin controls the state of the Data IO pins. If #OE is driven High (VIH), all Data IO pins will
remain at high impedance and if driven Low, the Data IO pins will drive data ( #OE has no affect on
the RY/BY# output pin).
7.2.6
Write Operation
To execute a write operation, Chip Enable (#CE) pin is driven Low and the Output Enable (#OE) is
pulled high to disable the Data IO pins to a high impedance state. The desired address and data
should be present on the appropriate pins. Addresses are latched on the falling edge of either #WE or
#CE and Data is latched on the rising edge or either #CE or #WE. To see an example, please refer to
timing diagrams in Figure 8-5 and Figure 8-15. If an invalid write instruction, not defined in this
datasheet is written to the device, it may put the device in an undefined state.
相關PDF資料
PDF描述
W948D6FBHX6G 8M X 16 DDR DRAM, 5 ns, PBGA60
WF128K32-120HC5 512K X 8 FLASH 5V PROM MODULE, 120 ns, CHIP66
WF128K32-90HM5 512K X 8 FLASH 5V PROM MODULE, 90 ns, CHIP66
WS128K32-35CJM 512K X 8 MULTI DEVICE SRAM MODULE, 35 ns, CQCC68
WS512K32F-100G2Q 2M X 8 MULTI DEVICE SRAM MODULE, 100 ns, QMA68
相關代理商/技術參數
參數描述
W29GL128C 制造商:WINBOND 制造商全稱:Winbond 功能描述:128M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE
W29GL128CH9B 功能描述:IC FLASH 128MBIT 90NS 64LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6
W29GL128CH9B TR 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 64LFBGA
W29GL128CH9T 功能描述:IC FLASH 128MBIT 90NS 56TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR)
W29GL128CH9T TR 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 56TSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*