- 您現在的位置：買賣IC網 > PDF目錄203625 > W25Q32DWZPIP (WINBOND ELECTRONICS CORP) 256K X 16 SPI BUS SERIAL EEPROM, 7.5 ns, PDSO8 PDF資料下載
參數資料
| 型號： | W25Q32DWZPIP |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 256K X 16 SPI BUS SERIAL EEPROM, 7.5 ns, PDSO8 |
| 封裝： | 6 X 5 MM, GREEN, WSON-8 |
| 文件頁數： | 78/82頁 |
| 文件大?。?/td> | 1155K |
| 代理商： | W25Q32DWZPIP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁
W25Q32DW
- 8 -
7.1
Package Types
At the time this datasheet was published, not all package types had been finalized. Contact Winbond to
confirm availability of these packages before designing to this specification. W25Q32DW is offered in an
8-pin plastic 208-mil width SOIC (package code SS), a WSON 6x5-mm or 8X6-mm (package code ZP &
ZE) and a 16-pin plastic 300-mil width SOIC (package code SF) as shown in Figure 1a, 1b, 1c. Package
diagrams and dimensions are illustrated at the end of this datasheet.
7.2
Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high, the device is
deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When
deselected, the devices power consumption will be at standby levels unless an internal erase, program or
write status register cycle is in progress. When /CS is brought low, the device will be selected, power
consumption will increase to active levels and instructions can be written to and data read from the
device. After power-up, /CS must transition from high to low before a new instruction will be accepted.
The /CS input must track the VCC supply level at power-up (see “Write Protection” and figure 43). If
needed a pull-up resister on /CS can be used to accomplish this.
7.3
Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)
The W25Q32DW supports standard SPI, Dual SPI, Quad SPI and QPI operation. Standard SPI
instructions use the unidirectional DI (input) pin to serially write instructions, addresses or data to the
device on the rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional
DO (output) to read data or status from the device on the falling edge of CLK.
Dual/Quad SPI and QPI instructions use the bidirectional IO pins to serially write instructions, addresses
or data to the device on the rising edge of CLK and read data or status from the device on the falling
edge of CLK. Quad SPI and QPI instructions require the non-volatile Quad Enable bit (QE) in Status
Register-2 to be set. When QE=1, the /WP pin becomes IO2 and /HOLD pin becomes IO3.
7.4
Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Registers from being written. Used in
conjunction with the Status Register’s Block Protect (CMP, SEC, TB, BP2, BP1 and BP0) bits and Status
Register Protect (SRP) bits, a portion as small as a 4KB sector or the entire memory array can be
hardware protected. The /WP pin is active low. However, when the QE bit of Status Register-2 is set for
Quad I/O, the /WP pin function is not available since this pin is used for IO2. See figure 1a, 1b and 1c for
the pin configuration of Quad I/O operation.
7.5
HOLD (/HOLD)
The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought low,
while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored
(don’t care). When /HOLD is brought high, device operation can resume. The /HOLD function can be
useful when multiple devices are sharing the same SPI signals. The /HOLD pin is active low. When the
QE bit of Status Register-2 is set for Quad I/O, the /HOLD pin function is not available since this pin is
used for IO3. See figure 1a, 1b and 1c for the pin configuration of Quad I/O operation.
7.6
Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI
Operations")
相關PDF資料 |
PDF描述 |
|---|---|
| W25Q80VZPIG | 1M X 8 SPI BUS SERIAL EEPROM, DSO8 |
| W25X16AVDAIZ | 2M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X40AVSSIG | 512K X 8 FLASH 2.7V PROM, PDSO8 |
| W25X80AVDAIZ | 1M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X80ALSSIG | 1M X 8 FLASH 2.7V PROM, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q32FVSFIG | 功能描述:IC FLASH SPI 32MBIT 16SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:72 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步 存儲容量:4.5M（256K x 18） 速度:133MHz 接口:并聯 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP（14x20） 包裝:托盤 |
| W25Q32FVSSIG | 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 3V/3.3V 32Mbit 4M x 8bit 8.5ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:32MB F VERSIOB SPI FLASH 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8SOIC |
| W25Q32FVSSIG TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8SOIC |
| W25Q32FVSSIQ | 制造商:Winbond Electronics Corp 功能描述: |
| W25Q32FVZPIG | 功能描述:IC FLASH SPI 32MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。