參數資料
型號: W25Q32DWZPIP
廠商: WINBOND ELECTRONICS CORP
元件分類: PROM
英文描述: 256K X 16 SPI BUS SERIAL EEPROM, 7.5 ns, PDSO8
封裝: 6 X 5 MM, GREEN, WSON-8
文件頁數: 18/82頁
文件大?。?/td> 1155K
代理商: W25Q32DWZPIP
W25Q32DW
Publication Release Date: January 18, 2011
- 25 -
Preliminary - Revision C
/CS
CLK
Mode 0
Mode 3
0
1
IO
0
IO
1
IO
2
IO
3
05h or 35h
2
3
4
5
4
0
4
0
5
1
6
2
7
3
5
1
6
2
7
3
4
5
6
7
SR1 or SR2
out
SR1 or SR2
out
Instruction
Figure 8b. Read Status Register Instruction (QPI Mode)
10.2.10
Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. Only non-volatile Status
Register bits SRP0, SEC, TB, BP2, BP1, BP0 (bits 7 thru 2 of Status Register-1) and CMP, LB3, LB2,
LB1, LB0, QE, SRP1 (bits 14 thru 8 of Status Register-2) can be written to. All other Status Register bit
locations are read-only and will not be affected by the Write Status Register instruction. LB3-0 are non-
volatile OTP bits, once it is set to 1, it can not be cleared to 0. The Status Register bits are shown in
Figure 4a and 4b, and described in 10.1.
To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously have
been executed for the device to accept the Write Status Register instruction (Status Register bit WEL
must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction
code “01h”, and then writing the status register data byte as illustrated in figure 9.
To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must
have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0).
However, SRP1 and LB3, LB2, LB1, LB0 can not be changed from “1” to “0” because of the OTP
protection for these bits. Upon power off or the execution of a “Reset (99h)” instruction, the volatile Status
Register bit values will be lost, and the non-volatile Status Register bit values will be restored.
To complete the Write Status Register instruction, the /CS pin must be driven high after the eighth or
sixteenth bit of data that is clocked in. If this is not done the Write Status Register instruction will not be
executed. If /CS is driven high after the eighth clock (compatible with the 25X series) the CMP, QE and
SRP1 bits will be cleared to 0.
During non-volatile Status Register write operation (06h combined with 01h), after /CS is driven high, the
self-timed Write Status Register cycle will commence for a time duration of tW (See AC Characteristics).
While the Write Status Register cycle is in progress, the Read Status Register instruction may still be
accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle
相關PDF資料
PDF描述
W25Q80VZPIG 1M X 8 SPI BUS SERIAL EEPROM, DSO8
W25X16AVDAIZ 2M X 8 FLASH 2.7V PROM, PDIP8
W25X40AVSSIG 512K X 8 FLASH 2.7V PROM, PDSO8
W25X80AVDAIZ 1M X 8 FLASH 2.7V PROM, PDIP8
W25X80ALSSIG 1M X 8 FLASH 2.7V PROM, PDSO8
相關代理商/技術參數
參數描述
W25Q32FVSFIG 功能描述:IC FLASH SPI 32MBIT 16SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:72 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步 存儲容量:4.5M(256K x 18) 速度:133MHz 接口:并聯 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP(14x20) 包裝:托盤
W25Q32FVSSIG 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 3V/3.3V 32Mbit 4M x 8bit 8.5ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:32MB F VERSIOB SPI FLASH 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8SOIC
W25Q32FVSSIG TR 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8SOIC
W25Q32FVSSIQ 制造商:Winbond Electronics Corp 功能描述:
W25Q32FVZPIG 功能描述:IC FLASH SPI 32MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?(單線) 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-MSOP 包裝:帶卷 (TR)