參數資料
型號: W25Q32DWZPIP
廠商: WINBOND ELECTRONICS CORP
元件分類: PROM
英文描述: 256K X 16 SPI BUS SERIAL EEPROM, 7.5 ns, PDSO8
封裝: 6 X 5 MM, GREEN, WSON-8
文件頁數: 31/82頁
文件大小: 1155K
代理商: W25Q32DWZPIP
W25Q32DW
Publication Release Date: January 18, 2011
- 37 -
Preliminary - Revision C
10.2.17 Word Read Quad I/O (E7h)
The Word Read Quad I/O (E7h) instruction is similar to the Fast Read Quad I/O (EBh) instruction except
that the lowest Address bit (A0) must equal 0 and only two Dummy clock are required prior to the data
output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code
execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status Register-2 must be set to
enable the Word Read Quad I/O Instruction.
Word Read Quad I/O with “Continuous Read Mode”
The Word Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in Figure 16a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Quad I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits M5-4 = (1,0), then the next Fast Read Quad I/O instruction (after /CS
is raised and then lowered) does not require the E7h instruction code, as shown in Figure 16b. This
reduces the instruction sequence by eight clocks and allows the Read address to be immediately entered
after /CS is asserted low. If the “Continuous Read Mode” bits M5-4 do not equal to (1,0), the next
instruction (after /CS is raised and then lowered) requires the first byte instruction code, thus returning to
normal operation. It is recommended to input FFh on IO0 for the next instruction (8 clocks), to ensure M4
= 1 and return the device to normal operation.
Figure 16a. Word Read Quad I/O Instruction (Initial instruction or previous M5-4
10, SPI Mode only)
M7-0
/CS
CLK
Mode 0
Mode 3
0
1
IO
0
IO
1
IO
2
IO
3
2
3
4
5
20
16
12
8
21
17
22
18
23
19
13
9
14
10
15
11
A23-16
6
7
8
9
4
0
5
1
6
2
7
3
A15-8
A7-0
Byte 1
Byte 2
4
0
5
1
6
2
7
3
4
0
5
1
6
2
7
3
4
0
5
1
6
2
7
3
10
11
12
13
14
4
5
6
7
IOs switch from
Input to Output
Byte 3
15
16
17
18
19
20
21
Dummy
Instruction (E7h)
相關PDF資料
PDF描述
W25Q80VZPIG 1M X 8 SPI BUS SERIAL EEPROM, DSO8
W25X16AVDAIZ 2M X 8 FLASH 2.7V PROM, PDIP8
W25X40AVSSIG 512K X 8 FLASH 2.7V PROM, PDSO8
W25X80AVDAIZ 1M X 8 FLASH 2.7V PROM, PDIP8
W25X80ALSSIG 1M X 8 FLASH 2.7V PROM, PDSO8
相關代理商/技術參數
參數描述
W25Q32FVSFIG 功能描述:IC FLASH SPI 32MBIT 16SOIC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:72 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步 存儲容量:4.5M(256K x 18) 速度:133MHz 接口:并聯 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP(14x20) 包裝:托盤
W25Q32FVSSIG 制造商:Winbond Electronics Corp 功能描述:Flash Serial-SPI 3V/3.3V 32Mbit 4M x 8bit 8.5ns 8-Pin SOIC 制造商:Winbond Electronics Corp 功能描述:32MB F VERSIOB SPI FLASH 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8SOIC
W25Q32FVSSIG TR 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 104MHZ 8SOIC
W25Q32FVSSIQ 制造商:Winbond Electronics Corp 功能描述:
W25Q32FVZPIG 功能描述:IC FLASH SPI 32MBIT 8WSON RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:SpiFlash® 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?(單線) 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP,8-MSOP(0.118",3.00mm 寬) 供應商設備封裝:8-MSOP 包裝:帶卷 (TR)