- 您現在的位置：買賣IC網 > PDF目錄202134 > W25Q32BVZEAG (WINBOND ELECTRONICS CORP) 32M X 1 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | W25Q32BVZEAG |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 32M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 8 X 6 MM, GREEN, WSON-8 |
| 文件頁數： | 35/79頁 |
| 文件大?。?/td> | 1090K |
| 代理商： | W25Q32BVZEAG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁
W25Q32BV
- 40 -
7.2.19 Continuous Read Mode Bits (M7-0)
The “Continuous Read Mode” bits are used in conjunction with “Fast Read Dual I/O”, “Fast Read Quad
I/O”, “Word Read Quad I/O” and “Octal Word Read Quad I/O” instructions to provide the highest random
Flash memory access rate with minimum SPI instruction overhead, thus allow true XIP (execute in place)
to be performed on serial flash devices.
M7-0 need to be set by the Dual/Quad I/O Read instructions. M5-4 are used to control whether the 8-bit
SPI instruction code (BBh, EBh, E7h or E3h) is needed or not for the next command. When M5-4 = (1,0),
the next command will be treated same as the current Dual/Quad I/O Read command without needing the
8-bit instruction code; when M5-4 do not equal to (1,0), the device returns to normal SPI mode, all
commands can be accepted. M7-6 and M3-0 are reserved bits for future use, either 0 or 1 values can be
used.
7.2.20 Continuous Read Mode Reset (FFh or FFFFh)
Continuous Read Mode Reset instruction can be used to set M4 = 1, thus the device will release the
Continuous Read Mode and return to normal SPI operation, as shown in Figure 18.
/CS
CLK
Mode 0
Mode 3
0
1
IO
0
IO
1
IO
2
IO
3
4
5
Don't Care
6
7
8
9
10
11
12
13
14
15
Mode Bit Reset
for Quad I/O (FFh)
Mode 0
Mode 3
Mode Bit Reset
for Dual I/O (FFFFh)
Don't Care
Figure 18. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
Since W25Q32BV does not have a hardware Reset pin, so if the controller resets while W25Q32BV is set
to Continuous Mode Read, the W25Q32BV will not recognize any initial standard SPI instructions from the
controller. To address this possibility, it is recommended to issue a Continuous Read Mode Reset
instruction as the first instruction after a system Reset. Doing so will release the device from the
Continuous Read Mode and allow Standard SPI instructions to be recognized.
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
相關PDF資料 |
PDF描述 |
|---|---|
| W3EG6466S335AD4M | 64M X 64 DDR DRAM MODULE, 0.7 ns, DMA200 |
| W3EG7264S335AD4SG | 64M X 72 DDR DRAM MODULE, 0.7 ns, DMA200 |
| WF1M32B-120G2UI3A | 1M X 32 FLASH 3.3V PROM MODULE, 120 ns, CQFP68 |
| WF1M32B-120H1I3A | 1M X 32 FLASH 3.3V PROM MODULE, 120 ns, CPGA66 |
| WE128K32N-150G2TC | 128K X 32 EEPROM 5V MODULE, 125 ns, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W25Q32BVZEAP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q32BVZEIG | 制造商:Winbond Electronics Corp 功能描述:32MB SPI FLASH |
| W25Q32BVZEIP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q32BVZPAG | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q32BVZPAP | 制造商:WINBOND 制造商全稱:Winbond 功能描述:3V 32M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
發布緊急采購，3分鐘左右您將得到回復。