參數資料
型號： UPD72042
廠商： NEC Corp.
英文描述： LSI DEVICES FOR Inter Equipment BusTM (IEBusTM) PROTOCOL CONTROL
中文描述： LSI器件間設備BusTM（IEBusTM）協議控制
文件頁數： 31/92頁
文件大?。?/td> 373K
代理商： UPD72042
μ
PD72042
31
Data Sheet S14870EJ1V0DS00
Cautions 1. In standby mode (with STM of the FLG register set to 1), the user can only write to the CTR
register (including standby mode cancellation) and read from the FLG register.
2. Never access a free address.
3. Slave status (SSR) can be read into RBF by setting the control bits to 0H or 6H from the master
unit.
CTR
Address
Read/write
When reset :
×××
00
××
1B
: 0000B (0H)
: Write
Control register
CTR is a one-byte write register used to control
μ
PD72042 operations.
[REEN]
When REEN is set to 1, the SLRE flag of the FLG register is immediately set to 1 to enable both slave and broadcast
reception.
[SRST]
When SRST is set to 1, the
μ
PD72042 is immediately reset. (Note, however, that STREQ is set to a written value.)
[STREQ]
1: Requests standby mode.
0: Exits from standby mode.
Standby mode setting and cancellation
The
μ
PD72042 is requested to enter the standby mode by setting the STREQ flag to 1 from the microcomputer.
The
μ
PD72042 enters standby mode when the standby mode input enabled state (carrier sense state) is set. In
this case, the impedance of the BUS+ and BUS– pins goes high (logic 1), and the STM flag of the FLG register
is set to 1. In standby mode, oscillation is stopped, and all operations are stopped while preserving the internal
data, thus minimizing power consumption.
When, in standby mode, the STREQ flag is set to 0 from the microcomputer, standby mode is cancelled
after the period (about 20 ms) needed for oscillation to stabilize; the halted operations are resumed from the point
at which standby mode was set. At this time, the STM flag of the FLG register changes to 0.
In standby mode, only writing to the CTR register (for standby mode cancellation) and reading from the FLG register
can be performed from the microcomputer.
Cautions 1. When the SRST flag and STREQ flag are simultaneously set to 1, standby mode is set after
software reset. (This state is the same as that set by hardware reset.) Note, however, that
when the SRST flag is set to 1 in standby mode, a software reset is performed, but this is not
reflected in the FLG register.
2. Do not read any data from internal registers via the serial I/O during the period from when a
microcomputer sets the STREQ flag to 1 to when the
μ
PD72042 enters the standby mode. This
period is one-communication frame at maximum.
b7
—
b6
—
b5
—
b4
b3
b0
—
CTR
b2
b1
REEN
SRST
—
STREQ
相關PDF資料
PDF描述
UPD72042GT LSI DEVICES FOR Inter Equipment BusTM (IEBusTM) PROTOCOL CONTROL
uPD72107GC-3B9 LAP-B CONTROLLER(Link Access Procedure Balanced mode)
UPD72107 LAP-B CONTROLLER(Link Access Procedure Balanced mode)
uPD72107CW LAP-B CONTROLLER(Link Access Procedure Balanced mode)
uPD72107L LAP-B CONTROLLER(Link Access Procedure Balanced mode)
相關代理商/技術參數
參數描述
UPD72042BGT-A 制造商:Renesas Electronics 功能描述:LSI Device 16-Pin SOP 制造商:Renesas Electronics 功能描述:LSI Device 16-Pin SOP Cut Tape
UPD72042GT(A) 制造商:Renesas Electronics Corporation 功能描述:
UPD720902AF5-667-JF2-E3-A 功能描述:IC ADVANCED MEMORY BUFFER D1 RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:* 標準包裝:90 系列:- 應用:PCI 至 PCI 橋 接口:PCI 電源電壓:3 V ~ 3.6 V 封裝/外殼:257-LFBGA 供應商設備封裝:257-BGA MICROSTAR（16x16） 包裝:托盤 安裝類型:表面貼裝 產品目錄頁面:882 (CN2011-ZH PDF) 其它名稱:296-19316
UPD72255YF1-GA5-A 制造商:Renesas Electronics Corporation 功能描述:
UPD7225G 制造商:Panasonic Industrial Company 功能描述:IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*