
www.ti.com
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range, T version (unless otherwise noted)
(1)
TMS470R1B768
16/32-Bit RISC Flash Microcontroller
SPNS108A–AUGUST 2005–REVISED AUGUST 2006
PARAMETER
TEST CONDITIONS
MIN
0.15
TYP
MAX
UNIT
V
V
hys
Input hysteresis
All inputs
(2)
except
OSCIN
OSCIN only
All inputs except
OSCIN
OSCIN only
AWD only
–0.3
0.8
V
IL
Low-level input voltage
V
–0.3
0.35 V
CC
2
V
CCIO
+ 0.3
V
IH
High-level input voltage
V
0.65 V
CC
1.35
V
CC
+ 0.3
1.8
V
th
Input threshold voltage
Drain to source on
resistance
V
RDS
ON
AWD only
(3)
V
OL
= 0.35 V at I
OL
= 2mA
175
I
OL
= I
OL
MAX
I
OL
= 50 μA
I
OH
= I
OH
MIN
I
OH
= 50 μA
V
I
< V
SSIO
– 0.3 or
V
I
> V
CCIO
+ 0.3
V
I
= V
SS
V
I
= V
CCIO
V
I
= V
SS
V
I
= V
CCIO
No pullup or pulldown
0.2 V
CCIO
0.2
V
OL
Low-level output voltage
(4)
V
0.8 V
CCIO
V
CCIO
– 0.2
V
OH
High-level output voltage
(4)
V
I
IC
Input clamp current (I/O pins)
(5)
–2
2
mA
I
IL
Pulldown
I
IH
Pulldown
I
IL
Pullup
I
IH
Pullup
All other pins
CLKOUT, TDO
RST, SPInCLK,
SPInSOMI,
SPInSIMO
(6)
All other output
pins
(7)
CLKOUT, TDO
RST, SPInCLK,
SPInSOMI,
SPInSIMO
(6)
All other output
pins except RST
(7)
–1
5
–40
–1
–1
1
40
–5
1
1
8
I
I
Input current (I/O pins)
μA
4
I
OL
Low-level output current
V
OL
= V
OL
MAX
mA
2
–8
–4
I
OH
High-level output current
V
OH
= V
OH
MIN
mA
–2
SYSCLK = 60 MHz,
ICLK = 20 MHz, V
CC
= 2.05 V
SYSCLK = 24 MHz,
ICLK = 12 MHz, V
CC
= 2.05 V
OSCIN = 6 MHz, V
CC
= 2.05 V
All frequencies, V
CC
= 2.05 V
No DC load, V
CCIO
= 3.6 V
(8)
No DC load, V
CCIO
= 3.6 V
(8)
No DC load, V
CCIO
= 3.6 V
(8)
135
mA
V
CC
Digital supply current (operating mode)
105
mA
I
CC
V
CC
Digital supply current (standby mode)
(8)
V
CC
Digital supply current (halt mode)
(8)
V
CCIO
Digital supply current (operating mode)
V
CCIO
Digital supply current (standby mode)
V
CCIO
Digital supply current (halt mode)
4
2
10
300
300
mA
mA
mA
μA
μA
I
CCIO
(1)
(2)
(3)
Source currents (out of the device) are negative while sink currents (into the device) are positive.
This does not apply to the PORRST pin. For PORRST exceptions, see the
RST and PORRST timings
section.
These values help to determine the external RC network circuit. For more details, see the
TMS470R1x System Module Reference Guide
(literature number SPNU189).
V
and V
are linear with respect to the amount of load current (I
OL
/I
OH
) applied.
Parameter does not apply to input-only or output-only pins.
n = 1–5.
The 2 mA buffers on this device are called zero-dominant buffers. If two of these buffers are shorted together and one is outputting a
low level and the other is outputting a high level, the resulting value will always be low.
I/O pins configured as inputs or outputs with no load. All pulldown inputs
≤
0.2 V. All pullup inputs
≥
V
CCIO
– 0.2 V.
(4)
(5)
(6)
(7)
(8)
25
Submit Documentation Feedback