參數資料
型號: ST7PLU09MCTRE
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
封裝: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件頁數: 36/124頁
文件大?。?/td> 1995K
代理商: ST7PLU09MCTRE
ST7LUS5, ST7LU05, ST7LU09
Flash program memory
Depending on the ICP driver code downloaded in RAM, Flash memory programming can be
fully customized (number of bytes to program, program locations, or selection of the serial
communication interface for downloading).
4.3.2
In-application programming (IAP)
This mode uses an IAP driver program previously programmed in Sector 0 by the user (in
ICP mode).
This mode is fully controlled by user software. This allows it to be adapted to the user
application (user-defined strategy for entering programming mode or choice of
communications protocol used to fetch the data to be stored, etc.).
IAP mode can be used to program any memory areas except Sector 0, which is write/erase
protected to allow recovery in case errors occur during the programming operation.
4.4
ICC interface
ICP needs a minimum of 4 and up to 6 pins to be connected to the programming tool. These
pins are:
RESET:
device reset
VSS:
device power supply ground
ICCCLK:
ICC output serial clock pin(a)
ICCDATA: ICC input serial data pin
CLKIN:
main clock input for external source
VDD:
application board power supply(b)
a.
If the ICCCLK or ICCDATA pins are only used as outputs in the application, no signal isolation is necessary. As
soon as the programming tool is plugged to the board, even if an ICC session is not in progress, the ICCCLK
and ICCDATA pins are not available for the application. If they are used as inputs by the application, isolation
such as a serial resistor has to be implemented in case another device forces the signal. Refer to the
programming tool documentation for recommended resistor values.
b.
The use of Pin 7 of the ICC connector depends on the programming tool architecture. This pin must be
connected when using most ST programming tools (it is used to monitor the application power supply). Please
refer to the programming tool manual.
相關PDF資料
PDF描述
ST7PLU05MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST7PLU09MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST90135M5T6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90T158M9Q6 16-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90158M9Q6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI