參數資料
型號： ST10R272LT6
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, TQFP-100
文件頁數： 43/77頁
文件大小： 707K
代理商： ST10R272LT6
48/77
ST10R272L - ELECTRICAL CHARACTERISTICS
Prescaler operation
Set when pins P0.15-13 (P0H.7-5) equal ’001’ during reset, the CPU clock is derived from the
internal oscillator (input clock signal) by a 2:1 prescaler.
The frequency of fCPU is half the frequency of fXTAL and the high and low time of fCPU (i.e. the
duration of an individual TCL) is defined by the period of the input clock fXTAL.
The timings listed in the AC characteristics that refer to TCLs therefore can be calculated
using the period of fXTAL for any TCL.
Note that if the bit OWDDIS in SYSCON register is cleared, the PLL runs on its free-running
frequency and delivers the clock signal for the Oscillator Watchdog. If bit OWDDIS is set, then
the PLL is switched off.
Direct drive
When pins P0.15-13 (P0H.7-5) equal ’011’ during reset, the on-chip phase locked loop is
disabled and the CPU clock is driven from the internal oscillator with the input clock signal.
The frequency of fCPU directly follows the frequency of fXTAL so the high and low time of fCPU
(i.e. the duration of an individual TCL) is defined by the duty cycle of the input clock fXTAL.
The TCL timing below must be calculated using the minimum possible TCL which can be
calculated by the formula:
For two consecutive TCLs the deviation caused by the duty cycle of fXTAL is compensated so
the duration of 2TCL is always 1/fXTAL. Therefore, the minimum value TCLmin has to be used
only once for timings that require an odd number of TCLs (1,3,...). Timings that require an
even number of TCLs (2,4,...) may use the formula:
.
100
F
XTAL * 5
2 to 10 MHz
011
F
XTAL * 1
1 to 50 MHz
Direct drive 1)
010
F
XTAL * 1.5
6.66 to 33.33 MHz
001
F
XTAL / 2
2 to 100 MHz
CPU clock via 2:1 prescaler
000
F
XTAL * 2.5
4 to 20 MHz
1) The maximum depends on the duty cycle of the external clock signal. The maxi-
mum input frequency is 25 MHz when using an external crystal oscillator, but
higher frequencies can be applied with an external clock source.
P0.15-13 (P0H.7-5)
CPU frequency
fCPU = fXTAL * F
External clock
input range 10-
50MHz
Notes
Table 15 CPU clock generation mechanisms
TCL
min
1 f
XTAL
DC
min
×
DC
(
=
duty cycle
)
=
2TCL
1 f
XTAL
=
1
相關PDF資料
PDF描述
ST16C452PSIJ68 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68
ST16C452ATIJ68 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68
ST16C654IQ64/TR 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQFP64
ST18931CR 16-BIT, 50 MHz, OTHER DSP, CPGA121
ST40RA150XH6 32-BIT, 150 MHz, RISC PROCESSOR, PBGA372
相關代理商/技術參數
參數描述
ST10-S 功能描述:電機驅動器 RoHS:否 制造商:Applied Motion 電機驅動類型:2035 Step 電源電壓:12 V to 35 V 功率額定值:70 W 每轉步距分辨率:200 to 400 框架大小 (NEMA):
ST10-S (5000-127) 功能描述:電機驅動器 RoHS:否 制造商:Applied Motion 電機驅動類型:2035 Step 電源電壓:12 V to 35 V 功率額定值:70 W 每轉步距分辨率:200 to 400 框架大小 (NEMA):
ST10S008V4AR1800 功能描述:記憶卡連接器 Micro SD Conn P/P 1.25x13.2x14.85mm RoHS:否 制造商:Yamaichi Electronics 產品:Card Connectors 卡類型:microSD 類型: 節距: 方向: 安裝風格:SMD/SMT 端接類型: 排數: 觸點數量: 電流額定值:0.5 A 電壓額定值:50 V
ST10S008V4B 制造商:JAE 制造商全稱:JAE 功能描述:microSDTM Small Memory Card Connector
ST10S008V4BR1800 功能描述:記憶卡連接器 microSD PUSH-PUSH LOW PROFILE 1.25MM H RoHS:否 制造商:Yamaichi Electronics 產品:Card Connectors 卡類型:microSD 類型: 節距: 方向: 安裝風格:SMD/SMT 端接類型: 排數: 觸點數量: 電流額定值:0.5 A 電壓額定值:50 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*