參數資料
型號： ST10R272LT6
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： 16-BIT, 50 MHz, MICROCONTROLLER, PQFP100
封裝： 14 X 14 MM, TQFP-100
文件頁數： 20/77頁
文件大小： 707K
代理商： ST10R272LT6
27/77
ST10R272L - GENERAL PURPOSE TIMERS
10
GENERAL PURPOSE TIMERS
The GPTs are flexible multifunctional timer/counters used for time-related tasks such as event
timing and counting, pulse width and duty cycle measurements, pulse generation or pulse
multiplication. The GPT unit contains five 16-bit timers, organized in two separate modules,
GPT1 and GPT2. Each timer in each module may operate independently in a number of
different modes, or may be concatenated with another timer of the same module.
10.1 GPT1
Each of the three timers T2, T3, T4 of the GPT1 module can be configured individually for one
of four basic modes of operation: timer, gated timer, counter mode and incremental
interface mode. In timer mode, the input clock for a timer is derived from the CPU clock,
divided by a programmable prescaler. In counter mode, the timer is clocked in reference to
external events. Pulse width or duty cycle measurement is supported in gated timer mode
where the operation of a timer is controlled by the ‘gate’ level on an external input pin. For
these purposes, each timer has one associated port pin (TxIN) which serves as gate or clock
input. Table 8 GPT1 timer input frequencies, resolution and periods lists the timer input
frequencies, resolution and periods for each pre-scaler option at 50MHz CPU clock. This also
applies to the Gated Timer Mode of T3 and to the auxiliary timers T2 and T4 in Timer and
Gated Timer Mode
The count direction (up/down) for each timer is programmable by software or may additionally
be altered dynamically by an external signal on a port pin (TxEUD).
In Incremental Interface Mode, the GPT1 timers (T2, T3, T4) can be directly connected to the
incremental position sensor signals A and B by their respective inputs TxIN and TxEUD.
Direction and count signals are internally derived from these two input signals so that the
contents of the respective timer Tx corresponds to the sensor position. The third position
sensor signal TOP0 can be connected to an interrupt input.
Timer T3 has output toggle latches (TxOTL) which changes state on each timer over-flow/
underflow. The state of this latch may be output on port pins (TxOUT) e. g. for time out
monitoring of external hardware components, or may be used internally to clock timers T2 and
T4 for measuring long time periods with high resolution.
In addition to their basic operating modes, timers T2 and T4 may be configured as reload or
capture registers for timer T3. When used as capture or reload registers, timers T2 and T4 are
stopped. The contents of timer T3 is captured into T2 or T4 in response to a signal at their
associated input pins (TxIN). Timer T3 is reloaded with the contents of T2 or T4 triggered
either by an external signal or by a selectable state transition of its toggle latch T3OTL. When
both T2 and T4 are configured to alternately reload T3 on opposite state transitions of T3OTL
with the low and high times of a PWM signal, this signal can be constantly generated without
software intervention.
1
相關PDF資料
PDF描述
ST16C452PSIJ68 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68
ST16C452ATIJ68 2 CHANNEL(S), SERIAL COMM CONTROLLER, PQCC68
ST16C654IQ64/TR 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQFP64
ST18931CR 16-BIT, 50 MHz, OTHER DSP, CPGA121
ST40RA150XH6 32-BIT, 150 MHz, RISC PROCESSOR, PBGA372
相關代理商/技術參數
參數描述
ST10-S 功能描述:電機驅動器 RoHS:否 制造商:Applied Motion 電機驅動類型:2035 Step 電源電壓:12 V to 35 V 功率額定值:70 W 每轉步距分辨率:200 to 400 框架大小 (NEMA):
ST10-S (5000-127) 功能描述:電機驅動器 RoHS:否 制造商:Applied Motion 電機驅動類型:2035 Step 電源電壓:12 V to 35 V 功率額定值:70 W 每轉步距分辨率:200 to 400 框架大小 (NEMA):
ST10S008V4AR1800 功能描述:記憶卡連接器 Micro SD Conn P/P 1.25x13.2x14.85mm RoHS:否 制造商:Yamaichi Electronics 產品:Card Connectors 卡類型:microSD 類型: 節距: 方向: 安裝風格:SMD/SMT 端接類型: 排數: 觸點數量: 電流額定值:0.5 A 電壓額定值:50 V
ST10S008V4B 制造商:JAE 制造商全稱:JAE 功能描述:microSDTM Small Memory Card Connector
ST10S008V4BR1800 功能描述:記憶卡連接器 microSD PUSH-PUSH LOW PROFILE 1.25MM H RoHS:否 制造商:Yamaichi Electronics 產品:Card Connectors 卡類型:microSD 類型: 節距: 方向: 安裝風格:SMD/SMT 端接類型: 排數: 觸點數量: 電流額定值:0.5 A 電壓額定值:50 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*