- 您現在的位置：買賣IC網 > PDF目錄299877 > S29GL032N90BFI32 (SPANSION LLC) 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 PDF資料下載
參數資料
| 型號： | S29GL032N90BFI32 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封裝： | 8.15 X 6.15 MM, LEAD FREE, FBGA-48 |
| 文件頁數： | 43/81頁 |
| 文件大小： | 3095K |
| 代理商： | S29GL032N90BFI32 |
48
S29GL-N MirrorBit Flash Family
S29GL-N_01_12 October 29, 2008
Da ta
Sh e e t
10.7
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed
by the address of the sector to be erased, and the sector erase command. Table 10.1 on page 51 and
Table 10.3 on page 53 shows the address and data requirements for the sector erase command sequence.
The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase.
The system is not required to provide any controls or timings during these operations.
After the command sequence is written, a sector erase time-out of 50 s occurs. During the time-out period,
additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may
be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between
these additional cycles must be less than 50 s, otherwise erasure may begin. Any sector erase address and
command following the exceeded time-out may or may not be accepted. It is recommended that processor
interrupts be disabled during this time to ensure all commands are accepted. The interrupts can be
re-enabled after the last Sector Erase command is written. Any command other than Sector Erase or
Erase Suspend during the time-out period resets the device to the read mode. Note that the Secured
Silicon Sector, autoselect, and CFI functions are unavailable when an erase operation is in progress.
The system must rewrite the command sequence and any additional addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3:
Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in the command
sequence.
When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses
are no longer latched. The system can determine the status of the erase operation by reading DQ7, DQ6, or
DQ2 in the erasing sector. Refer to the Write Operation Status section for information on these status bits.
Once the sector erase operation begins, only the Erase Suspend command is valid. All other commands are
ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the
sector erase command sequence should be reinitiated once the device returns to reading array data, to
ensure data integrity.
Figure 10.4 on page 49 illustrates the algorithm for the erase operation. Refer to Table 15.3 on page 67 for
parameters, and Figure 15.7 on page 69 for timing diagrams.
相關PDF資料 |
PDF描述 |
|---|---|
| S2A | SURFACE MOUNT RECTIFIER |
| S2B | SURFACE MOUNT RECTIFIER |
| S2C1R-1-5-H | 4000 MHz - 8000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.7 dB INSERTION LOSS |
| S2D | SURFACE MOUNT RECTIFIER |
| S2G | SURFACE MOUNT RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032N90DFI020 | 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:260 |
| S29GL032N90DFI023 | 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:1 |
| S29GL032N90FAI030 | 制造商:Spansion 功能描述:IC, FLASH - Trays |
| S29GL032N90FAI040 | 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29GL032N90FFI010 | 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。