參數資料
型號： S29GL032N90BFI32
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 90 ns, PBGA48
封裝： 8.15 X 6.15 MM, LEAD FREE, FBGA-48
文件頁數： 37/81頁
文件大?。?/td> 3095K
代理商： S29GL032N90BFI32
42
S29GL-N MirrorBit Flash Family
S29GL-N_01_12 October 29, 2008
Da ta
Sh e e t
10.3
Autoselect Command Sequence
The autoselect command sequence allows the host system to read several identifier codes at specific
addresses:
Note
The device ID is read over three cycles. SA = Sector Address
The autoselect command sequence is initiated by first writing on unlock cycle (two cycles). This is followed by
a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The
system may read at any address any number of times without initiating another autoselect command
sequence:
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the
device was previously in Erase Suspend).
10.4
Enter/Exit Secured Silicon Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an 8-word/16-byte random
Electronic Serial Number (ESN). The system can access the Secured Silicon Sector region by issuing the
three-cycle Enter Secured Silicon Sector command sequence. The device continues to access the Secured
Silicon Sector region until the system issues the four-cycle Exit Secured Silicon Sector command sequence.
The Exit Secured Silicon Sector command sequence returns the device to normal operation. Table 10.1
on page 51 and Table 10.3 on page 53 show the address and data requirements for both command
sequences. See also Secured Silicon Sector Flash Memory Region on page 35 for further information. Note
that the ACC function and unlock bypass modes are not available when the Secured Silicon Sector is
enabled.
10.4.1
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two
unlock write cycles, followed by the program set-up command. The program address and data are written
next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further
controls or timings. The device automatically provides internally generated program pulses and verifies the
programmed cell margin. Table 10.1 on page 51 and Table 10.3 on page 53 show the address and data
requirements for the word program command sequence, respectively.
When the Embedded Program algorithm is complete, the device then returns to the read mode and
addresses are no longer latched. The system can determine the status of the program operation by using
DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits. Any commands
written to the device during the Embedded Program Algorithm are ignored. Note that the Secured Silicon
Sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Note that a
hardware reset immediately terminates the program operation. The program command sequence should be
reinitiated once the device returns to the read mode, to ensure data integrity.
Programming is allowed in any sequence of address locations and across sector boundaries. Programming
to the same word address multiple times without intervening erases (incremental bit programming) requires a
modified programming method. For such application requirements, please contact your local Spansion
representative. Word programming is supported for backward compatibility with existing Flash driver software
and for occasional writing of individual words. Use of write buffer programming (see below) is strongly
recommended for general programming use when more than a few words are to be programmed. The
effective word programming time using write buffer programming is approximately four times shorter than the
single word programming time.
Identifier Code
A7:A0
(x16)
A6:A-1
(x8)
Manufacturer ID
00h
Device ID, Cycle 1
01h
02h
Device ID, Cycle 2
0Eh
1Ch
Device ID, Cycle 3
0Fh
1Eh
Secured Silicon Sector Factory Protect
03h
06h
Sector Protect Verify
(SA)02h
(SA)04h
相關PDF資料
PDF描述
S2A SURFACE MOUNT RECTIFIER
S2B SURFACE MOUNT RECTIFIER
S2C1R-1-5-H 4000 MHz - 8000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.7 dB INSERTION LOSS
S2D SURFACE MOUNT RECTIFIER
S2G SURFACE MOUNT RECTIFIER
相關代理商/技術參數
參數描述
S29GL032N90DFI020 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:260
S29GL032N90DFI023 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:1
S29GL032N90FAI030 制造商:Spansion 功能描述:IC, FLASH - Trays
S29GL032N90FAI040 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29GL032N90FFI010 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*