- 您現在的位置：買賣IC網 > PDF目錄382465 > S1D15G10D08B000 (愛普生（中國）有限公司) LCD drivers equipped with the liquid crystal drive power circuit PDF資料下載
參數資料
| 型號： | S1D15G10D08B000 |
| 廠商： | 愛普生（中國）有限公司 |
| 英文描述： | LCD drivers equipped with the liquid crystal drive power circuit |
| 中文描述： | 與液晶驅動電源電路配備LCD驅動器 |
| 文件頁數： | 43/64頁 |
| 文件大?。?/td> | 434K |
| 代理商： | S1D15G10D08B000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
S1D15G10D08B000
40
EPSON
Rev. 1.0
(33) Read Register 1 (EPSRRD2) Command: 1 Parameter: 0
Issue the EPSRRD1 and STREAD (Status Read) commands in succession to read the built-in resistance ratio.
Issue the Status Read command immediately after this command. Also, always issue the NOP command after the
STREAD (Status Read) command.
A0
0
RD
1
WR
0
D7
0
D6
1
D5
1
D4
1
D3
1
D2
1
D1
0
D0
1
Command
(29) Cancel EEPROM Control (EPCOUT) Command: 1 Parameter: 0
This command cancels the EEPROM (S1F17A10) Control mode. If data is read from the EEPROM, both of Electronic
Control value and built-in resistance ratio are updated by the read data.
(30) Write Into EEPROM (EPMWR) Command: 1 Parameter: 0
This command writes the Electronic Control value and built-in resistance ratio into the EEPROM (S1F17A10).
(31) Read From EEPROM (EPMRD) Command: 1 Parameter: 0
This command reads the Electronic Control value and built-in resistance ratio from the EEPROM (S1F17A10), and
temporarily stores them in S1D15G10 registers.
(32) Read Register 1 (EPSRRD1) Command: 1 Parameter: 0
Issue the EPSRRD1 and STREAD (Status Read) commands in succession to read the Electronic Control value.
Issue the Status Read command immediately after this command. Also, always issue the NOP command after the
STREAD (Status Read) command.
A0
0
RD
1
WR
0
D7
1
D6
1
D5
1
D4
1
D3
1
D2
1
D1
0
D0
0
Command
A0
0
RD
1
WR
0
D7
1
D6
1
D5
1
D4
1
D3
1
D2
1
D1
0
D0
1
Command
A0
0
RD
1
WR
0
D7
0
D6
1
D5
1
D4
1
D3
1
D2
1
D1
0
D0
0
Command
A0
0
RD
1
WR
0
D7
1
D6
1
D5
0
D4
0
D3
1
D2
1
D1
0
D0
0
Command
(28) Control EEPROM (EPCTIN) Command: 1 Parameter: 1
This command with its parameter selects the EEPROM (S1F17A10) Control mode. The parameter can be set to either
Write or Read.
A0
RD
WR
D7
D6
D5
D4
Command
0
1
0
1
1
0
0
Parameter1 (P1)
1
1
0
*
*
P5
*
* Invalid bit; it is ignored during operation.
P5: Specifies data writing into or reading from the EEPROM (S1F17A10) as follows.
If P5=0: Read; if P5=1: Write
D3
1
*
D2
1
*
D1
0
*
D0
1
*
Function
––
Selects Write or Read.
P1: It specifies average temperature gradient.
P11
0
0
1
1
P10
0
1
0
1
Average temperature gradient [%/
°
C]
–
0.05
–
0.1
–
0.15
–
0.2
P2 to P14: Set the parameter as the table shown previously.
相關PDF資料 |
PDF描述 |
|---|---|
| S1L50000 | HIGH DENSITY GATE ARRAY |
| S1L51253 | HIGH DENSITY GATE ARRAY |
| S1L51254 | HIGH DENSITY GATE ARRAY |
| S1L51772 | HIGH DENSITY GATE ARRAY |
| S1L51773 | HIGH DENSITY GATE ARRAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1D19105 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:S1D19105d01b000 |
| S1D-1-E3 | 制造商:Vishay Semiconductors 功能描述:STANDARD RECOVERY POWER RECTIFIER FORWAR |
| S1D2140B03 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:R/G/B VIDEO AMPLIFIER WITH OSD INTERFACE FOR MONITORS |
| S1D2140B03-D0B0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:R/G/B VIDEO AMPLIFIER WITH OSD INTERFACE FOR MONITORS |
| S1D2141X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:R/G/B VIDEO AMPLIFIER FOR MONITORS |
發布緊急采購，3分鐘左右您將得到回復。