- 您現在的位置：買賣IC網 > PDF目錄382465 > S1D15G10D08B000 (愛普生（中國）有限公司) LCD drivers equipped with the liquid crystal drive power circuit PDF資料下載
參數資料
| 型號： | S1D15G10D08B000 |
| 廠商： | 愛普生（中國）有限公司 |
| 英文描述： | LCD drivers equipped with the liquid crystal drive power circuit |
| 中文描述： | 與液晶驅動電源電路配備LCD驅動器 |
| 文件頁數： | 39/64頁 |
| 文件大?。?/td> | 434K |
| 代理商： | S1D15G10D08B000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
S1D15G10D08B000
36
EPSON
Rev. 1.0
(15) Partial in (PTLIN) Command: 1 Parameter: 2
This command and succeeding parameters specify the partial display area. This command is used to turn on partial
display of the screen (dividing screen by lines) in order to save power. Since S1D15G10 processes the liquid crystal
display signals on 4-line basis (block basis), the display and non-display areas are also specified on 4-bit line (block
basis).
*: Invalid bits irrelevant with the operation.
A block address that can be specified for the partial display must be the displayed one (don’t try to specify an address
not to be displayed when scrolled).
When the partial display mode is turned on, following state is introduced to S1D15G10 in the non-display area:
* LOW is output to DOFF pin.
* All COM pins output V
C
.
* All SEG pins output V
1
or MV
1
.
SEG output is forced to V
1
or MV
1
depending on state of FR in the last display line. When FR is HIGH, V
1
is output
and when FR is LOW, MV
1
is output. Phase of FR is constantly reversed at start of a frame.
(16) Partial out (PTLOUT) Command: 1 Parameter: 0
This command is used to exit from the partial display mode.
A0
RD
WR
Command
0
1
0
(17) Read modify write in (RMWIN) Command: 1 Parameter: 0
This command is used along with the column address set command, page address set command and read modify write
out command. This function is used when frequently modifying data to specify a specific display area such as blinking
cursor. First set a specific display area using the column and page address commands. Then, enter this command to
set the column and page addresses at the start address of the specific area. When this operation is complete, the column
(page) address won’t be modified by the display data read command. It is incremented only when the display data write
command is used. You can cancel this mode by entering the read modify write out or any other command.
A0
0
1
1
RD
1
1
1
WR
0
0
0
D7
1
*
*
D6
0
*
*
D5
1
P15 P14 P13 P12 P11 P10
P25 P24 P23 P22 P21 P20
D4
0
D3
1
D2
0
D1
0
D0
0
Function
––
Command
Parameter1 (P1)
Parameter2 (P2)
Start block address
End block address
D7
1
D6
0
D5
1
D4
0
D3
1
D2
0
D1
0
D0
1
A0
0
RD
1
WR
0
D7
1
D6
1
D5
1
D4
0
D3
0
D2
0
D1
0
D0
0
Command
Page address set
Column address set
Read modify write in
Dummy read
Read modify write out
Is modification
complete
No
Yes
Data read
Data write
相關PDF資料 |
PDF描述 |
|---|---|
| S1L50000 | HIGH DENSITY GATE ARRAY |
| S1L51253 | HIGH DENSITY GATE ARRAY |
| S1L51254 | HIGH DENSITY GATE ARRAY |
| S1L51772 | HIGH DENSITY GATE ARRAY |
| S1L51773 | HIGH DENSITY GATE ARRAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1D19105 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:S1D19105d01b000 |
| S1D-1-E3 | 制造商:Vishay Semiconductors 功能描述:STANDARD RECOVERY POWER RECTIFIER FORWAR |
| S1D2140B03 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:R/G/B VIDEO AMPLIFIER WITH OSD INTERFACE FOR MONITORS |
| S1D2140B03-D0B0 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:R/G/B VIDEO AMPLIFIER WITH OSD INTERFACE FOR MONITORS |
| S1D2141X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:R/G/B VIDEO AMPLIFIER FOR MONITORS |
發布緊急采購，3分鐘左右您將得到回復。