- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C6P366D0A0100 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 PDF資料下載
參數資料
| 型號： | S1C6P366D0A0100 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, FLASH, 4.1 MHz, MICROCONTROLLER, UUC102 |
| 封裝： | DIE-102 |
| 文件頁數： | 51/84頁 |
| 文件大?。?/td> | 1740K |
| 代理商： | S1C6P366D0A0100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
S1C6P366 TECHNICAL MANUAL
EPSON
45
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (I/O Ports)
IOC00–IOC03: P0 port I/O control register (FF40H)
IOC10–IOC13: P1 port I/O control register (FF44H)
IOC20–IOC23: P2 port I/O control register (FF48H)
IOC30–IOC33: P3 port I/O control register (FF4CH)
IOC40–IOC43: P4 port I/O control register (FF50H)
The input and output modes of the I/O ports are set with these registers.
When "1" is written: Output mode
When "0" is written: Input mode
Reading: Valid
The input and output modes of the I/O ports are set in 1-bit unit.
Writing "1" to the I/O control register makes the corresponding I/O port enter the output mode, and
writing "0" induces the input mode.
At initial reset, these registers are all set to "0", so the I/O ports are in the input mode.
The I/O control registers of the ports that are set as input/output for the serial interface or A/D con-
verter can be used as general purpose registers that do not affect the input/output.
PUL00–PUL03: P0 port pull-up control register (FF41H)
PUL10–PUL13: P1 port pull-up control register (FF45H)
PUL20–PUL23: P2 port pull-up control register (FF49H)
PUL30–PUL33: P3 port pull-up control register (FF4DH)
The pull-up during the input mode are set with these registers.
When "1" is written: Pull-up ON
When "0" is written: Pull-up OFF
Reading: Valid
The built-in pull-up resistor which is turned ON during input mode is set to enable in 1-bit units. (The
pull-up resistor isavailable for the P10–P13, P20–P23, P30–P33 ports.)
By writing "1" to the pull-up control register, the corresponding I/O ports are pulled up (during input
mode), while writing "0" turns the pull-up function OFF.
At initial reset, these registers are all set to "1", so the pull-up function is set to ON.
The registers of the ports that are set as input/output for the serial interface or A/D converter can be
used as general purpose registers that do not affect the pull-up control.
The pull-up control registers of the port that are set as input for the serial interface function the same as
the I/O port.
4.6.6 Programming note
When in the input mode, I/O ports are changed from low to high by pull-up resistor, the rise of the
waveform is delayed on account of the time constant of the pull-up resistor and input gate capacitance.
Hence, when fetching input ports, set an appropriate wait time.
Particular care needs to be taken of the key scan during key matrix configuration.
Make this waiting time the amount of time or more calculated by the following expression.
10
× C × R
C: terminal capacitance 5 pF + parasitic capacitance ? pF
R: pull-up resistance 300 k
相關PDF資料 |
PDF描述 |
|---|---|
| S1C6P466D0A0A00 | MICROCONTROLLER, UUC140 |
| S1C6S2L7D | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, UUC58 |
| S1C6S2A7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2B7F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C6S2N7D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC58 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C-6-S | 制造商:GRIPCO 功能描述: |
| S1C7309X | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C7309X01 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:B/W CCD PROCESSOR |
| S1C88349 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
| S1C88649 | 制造商:EPSON 制造商全稱:EPSON 功能描述:8-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。