- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60A13F 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | S1C60A13F |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | PLASTIC, QFP14-80 |
| 文件頁數： | 82/104頁 |
| 文件大?。?/td> | 850K |
| 代理商： | S1C60A13F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
S1C60N13 TECHNICAL MANUAL
EPSON
71
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Interrupt and HALT)
4.16.1 Interrupt factors
Table 4.16.1.1 shows the factors for generating interrupt requests.
The interrupt flags are set to "1" depending on the corresponding interrupt factors.
The CPU operation is interrupted when any of the conditions below set an interrupt factor flag to "1".
The corresponding mask register is "1" (enabled)
The interrupt flag is "1" (EI)
The interrupt factor flag is a read-only register, but can be reset to "0" when the register data is read out.
At initial reset, the interrupt factor flags are reset to "0".
Note: Read the interrupt factor flags only in the DI status (interrupt flag = "0"). A malfunction could result
from read-out during the EI status (interrupt flag = "1").
Table 4.16.1.1 Interrupt factors
Interrupt factor
Clock timer 2 Hz falling edge
Clock timer 8 Hz falling edge
Clock timer 32 Hz falling edge
Stopwatch timer 1 Hz falling edge
Stopwatch timer 10 Hz falling edge
Serial interface
When 8-bit data input/output has completed
Input (K00–K03) port rising/falling edge
Input (K10) port rising/falling edge
Interrupt factor flag
TI2
(2E9HD2)
TI8
(2E9HD1)
TI32
(2E9HD0)
SWIT1 (2EAHD1)
SWIT0 (2EAHD0)
ISIO
(2F3HD0)
IK0
(2EAHD2)
IK1
(2EAHD3)
4.16.2 Specific masks and factor flags for interrupt
The interrupt factor flags can be masked by the corresponding interrupt mask registers.
The interrupt mask registers are read/write registers. They are enabled (interrupt authorized) when "1" is
written to them, and masked (interrupt inhibited) when "0" is written to them.
At initial reset, the interrupt mask register is set to "0".
Table 4.16.2.1 shows the correspondence between interrupt mask registers and interrupt factor flags.
Table 4.16.2.1 Interrupt mask registers and interrupt factor flags
Interrupt mask register
ETI2
(2E8HD2)
ETI8
(2E8HD1)
ETI32
(2E8HD0)
EISWIT1 (2E6HD1)
EISWIT0 (2E6HD0)
EISIO
(2F2HD0)
EIK03*
(2E5HD3)
EIK02*
(2E5HD2)
EIK01*
(2E5HD1)
EIK00*
(2E5HD0)
EIK10*
(2E7HD2)
Interrupt factor flag
TI2
(2E9HD2)
TI8
(2E9HD1)
TI32
(2E9HD0)
SWIT1 (2EAHD1)
SWIT0 (2EAHD0)
ISIO
(2F3HD0)
IK0
(2EAHD2)
IK1
(2EAHD3)
There is an interrupt mask register for each pin of the input ports.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60L16F0A0100 | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, PQFP80 |
| S1C60N01F | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP48 |
| S1C60N02D | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC52 |
| S1C60L02 | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| S1C60N04D | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60A16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。