參數資料
型號: S1C60A13F
元件分類: 微控制器/微處理器
英文描述: 4-BIT, MROM, 1.2 MHz, MICROCONTROLLER, PQFP80
封裝: PLASTIC, QFP14-80
文件頁數: 25/104頁
文件大小: 850K
代理商: S1C60A13F
S1C60N13 TECHNICAL MANUAL
EPSON
19
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Oscillation Circuit)
4.3.5 Control of oscillation circuit (S1C60A13)
Table 4.3.5.1 lists the control bits and their addresses for the oscillation circuit.
Table 4.3.5.1 Control bits of oscillation circuit
Address
Comment
D3
D2
Register
D1
D0
Name
Init 1
10
5 Undefined
1
2
Initial value at initial reset
Not set in the circuit
3
4
Always "0" being read
Reset (0) immediately after being read
2FEH
0
CLKCHG OSCC
IOC1
R
R/W
0 3
CLKCHG
OSCC
IOC1
2
0
OSC3
On
Output
OSC1
Off
Input
Unused
CPU clock switch
OSC3 oscillation On/Off
I/O control register (P10–P13)
OSCC: OSC3 oscillation control (2FEHD1)
Controls oscillation ON/OFF for the OSC3 oscillation circuit. (S1C60A13 only.)
When "1" is written : The OSC3 oscillation ON
When "0" is written : The OSC3 oscillation OFF
Read-out : Valid
When it is necessary to operate the CPU of the S1C60A13 at high speed, set OSCC to "1". At other times,
set it to "0" to reduce current consumption.
For S1C60N13 and S1C60L13, keep OSCC set to "0".
At initial reset, OSCC is set to "0".
CLKCHG: CPU clock switch (2FEHD2)
The CPU's operation clock is selected with this register. (S1C60A13 only.)
When "1" is written : OSC3 clock is selected
When "0" is written : OSC1 clock is selected
Read-out : Valid
When the S1C60A13's CPU clock is to be OSC3, set CLKCHG to "1"; for OSC1, set CLKCHG to "0". This
register cannot be controlled for S1C60N13 and S1C60L13, so that OSC1 is selected no matter what the set
value.
At initial reset, CLKCHG is set to "0".
4.3.6 Programming notes (S1C60A13)
(1) It takes at least 5 msec from the time the OSC3 oscillation circuit goes ON until the oscillation stabi-
lizes. Consequently, when switching the CPU operation clock from OSC1 to OSC3, do this after a
minimum of 5 msec have elapsed since the OSC3 oscillation went ON.
Further, the oscillation stabilization time varies depending on the external oscillator characteristics
and conditions of use, so allow ample margin when setting the wait time.
(2) When switching the clock form OSC3 to OSC1, use a separate instruction for switching the OSC3
oscillation OFF. An error in the CPU operation can result if this processing is performed at the same
time by the one instruction.
相關PDF資料
PDF描述
S1C60L16F0A0100 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, PQFP80
S1C60N01F 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP48
S1C60N02D 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, UUC52
S1C60L02 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60
S1C60N04D 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48
相關代理商/技術參數
參數描述
S1C60A16 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C60L05 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C60L08 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C60L16 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer
S1C60N05 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer