
PIC12C67X
DS30561B-page 94
1999 Microchip Technology Inc.
12.2
DC Characteristics:
PIC12LC671/672 (Commercial, Industrial)
PIC12LCE673/674 (Commercial, Industrial)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise specified)
Operating temperature
0°C
≤
T
A
≤
+70°C (commercial)
–40°C
≤
T
A
≤
+85°C (industrial)
Min
Typ Max Units
Param
No.
Characteristic
Sym
Conditions
D001
D002
Supply Voltage
RAM Data Retention
Voltage
(2)
V
DD
Start Voltage to
ensure Power-on Reset
V
DD
Rise Rate to ensure
Power-on Reset
Supply Current
(3)
V
DD
V
DR
2.5
5.5
V
V
1.5*
Device in SLEEP mode
D003
V
POR
V
SS
V
See section on Power-on Reset for details
D004
S
VDD
0.05*
V/ms
See section on Power-on Reset for details
D010
D010C
D010A
I
DD
—
—
—
0.4
0.4
15
2.1
2.1
33
mA
mA
μ
A
F
OSC
= 4MHz, V
DD
= 2.5V
XT and EXTRC mode (Note 4)
F
OSC
= 4MHz, V
DD
= 2.5V
INTRC mode (Note 6)
F
OSC
= 32kHz, V
DD
= 2.5V, WDT disabled
LP mode, Industrial Temperature
D020
D021
D021B
Power-down Current
(5)
I
PD
—
—
—
0.2
0.2
2.0
2.0
5
6
4
6
μ
A
μ
A
μ
A
μ
A
kHz
V
DD
= 2.5V, Commercial
V
DD
= 2.5V, Industrial
V
DD
= 2.5V, Commercial
V
DD
= 2.5V, Industrial
All temperatures
Watchdog Timer Current
I
WDT
LP Oscillator Operating
Frequency
INTRC/EXTRC Oscillator
Operating Frequency
XT Oscillator Operating
Frequency
HS Oscillator Operating
Frequency
These parameters are characterized but not tested.
Data in Typical ("Typ") column is based on characterization results at 25°C. This data is for design guidance only and is not
tested.
This is the limit to which V
DD
can be lowered in SLEEP mode without losing RAM data.
The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus loading, oscillator
type, bus rate, internal code execution pattern, and temperature also have an impact on the current consumption.
a) The test conditions for all I
DD
measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to V
SS
, T0CKI = V
DD
,
MCLR = V
DD
; WDT disabled.
b) For standby current measurements, the conditions are the same, except that the device is in SLEEP mode.
For EXTRC osc configuration, current through R
EXT
is not included. The current through the resistor can be estimated by the
formula:
Ir = V
DD
/2R
EXT
(mA) with R
EXT
in kOhm.
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the
part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
DD
or V
SS
.
INTRC calibration value is for 4MHz nominal at 5V, 25°C.
F
OSC
0
—
0
0
200
4
(6)
4
10
MHz
MHz
MHz
All temperatures
All temperatures
All temperatures
*
Note 1:
2:
3:
4:
5:
6: