- 您現在的位置：買賣IC網 > PDF目錄368023 > PIC12C67X (Microchip Technology Inc.) 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEPROM Data Memory PDF資料下載
參數資料
| 型號： | PIC12C67X |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEPROM Data Memory |
| 中文描述： | 8引腳，8位CMOS微控制器與A / D轉換器和EEPROM數據存儲器 |
| 文件頁數： | 51/129頁 |
| 文件大?。?/td> | 931K |
| 代理商： | PIC12C67X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁
1999 Microchip Technology Inc.
DS30561B-page 51
PIC12C67X
8.5
The A/D module can operate during SLEEP mode. This
requires that the A/D clock source be set to RC
(ADCS<1:0> =
11
). When the RC clock source is
selected, the A/D module waits one instruction cycle
before starting the conversion. This allows the
SLEEP
instruction to be executed, which eliminates all digital
switching noise from the conversion. When the conver-
sion is completed, the GO/DONE bit will be cleared,
and the result loaded into the ADRES Register. If the
A/D interrupt is enabled, the device will wake-up from
SLEEP. If the A/D interrupt is not enabled, the A/D mod-
ule will then be turned off, although the ADON bit will
remain set.
When the A/D clock source is another clock option (not
RC), a
SLEEP
instruction will cause the present conver-
sion to be aborted and the A/D module to be turned off,
though the ADON bit will remain set.
Turning off the A/D places the A/D module in its lowest
current consumption state.
A/D Operation During Sleep
8.6
The overall accuracy of the A/D is less than
±
1 LSb for
V
DD
= 5V
±
10% and the analog V
REF
= V
DD
. This over-
all accuracy includes offset error, full scale error, and
integral error. The A/D converter is monotonic over the
full V
DD
range. The resolution and accuracy may be
less when either the analog reference (V
DD
) is less than
5.0V or when the analog reference (V
REF
) is less than
V
DD
.
The maximum pin leakage current is specified in the
Device Data Sheet electrical specification, parameter
#D060.
In systems where the device frequency is low, use of
the A/D RC clock is preferred. At moderate to high fre-
quencies, T
AD
should be derived from the device oscil-
lator. T
AD
must not violate the minimum and should be
≤
8
μ
s for preferred operation. This is because T
AD
,
when derived from T
OSC
, is kept away from on-chip
phase clock transitions. This reduces, to a large extent,
the effects of digital switching noise. This is not possible
with the RC derived clock. The loss of accuracy due to
digital switching noise can be significant if many I/O
pins are active.
In systems where the device will enter SLEEP mode
after the start of the A/D conversion, the RC clock
source selection is required. In this mode, the digital
noise from the modules in SLEEP are stopped. This
method gives high accuracy.
A/D Accuracy/Error
Note:
For the A/D module to operate in SLEEP,
the A/D clock source must be set to RC
(ADCS<1:0> =
11
). To perform an A/D
conversion in SLEEP, the GO/DONE bit
must be set, followed by the
SLEEP
instruction.
8.7
A device reset forces all registers to their reset state.
This forces the A/D module to be turned off, and any
conversion is aborted. The value that is in the ADRES
register is not modified for a Reset. The ADRES regis-
ter will contain unknown data after a Power-on Reset.
Effects of a Reset
8.8
If the input voltage exceeds the rail values (V
SS
or V
DD
)
by greater than 0.2V, then the accuracy of the conver-
sion is out of specification.
Connection Considerations
An external RC filter is sometimes added for anti-
aliasing of the input signal. The R component should be
selected to ensure that the total source impedance is
kept under the 10 k
recommended specification. Any
external components connected (via hi-impedance) to
an analog input pin (capacitor, zener diode, etc.) should
have very little leakage current at the pin.
8.9
The ideal transfer function of the A/D converter is as fol-
lows: the first transition occurs when the analog input
voltage (V
AIN
) is 1 LSb (or Analog V
REF
/ 256)
(Figure 8-3).
Transfer Function
FIGURE 8-3:
A/D TRANSFER FUNCTION
Note:
For the PIC12C67X, care must be taken
when using the GP4 pin in A/D conversions
due to its proximity to the OSC1 pin.
D
FFh
FEh
04h
03h
02h
01h
00h
0
1
2
3
4
2
2
(
Analog input voltage
相關PDF資料 |
PDF描述 |
|---|---|
| pic12ce674 | 8-Pin, 8-Bit CMOS Microcontroller with A/D Converter(具A/D轉換器和EEPROM數據存儲器的8位微控制器) |
| PIC12CR509A | 8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12F505 | 8/14-Pin, 8-Bit Flash Microcontrollers |
| PIC12F506 | 8/14-Pin, 8-Bit Flash Microcontroller |
| PIC12F510_07 | 8/14-Pin, 8-Bit Flash Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12C67X_13 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter and EEPROM Data Memory |
| PIC12CE-04/EJW | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12CE-04/EP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12CE-04/ESM | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
| PIC12CE-04/ESN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。