參數資料
型號： NAND256W4A2AZA6E
廠商： NUMONYX
元件分類： PROM
英文描述： 16M X 16 FLASH 3V PROM, 12000 ns, PBGA55
封裝： 8 X 10 MM, 1 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, VFBGA-55
文件頁數： 19/58頁
文件大?。?/td> 1406K
代理商： NAND256W4A2AZA6E
Device operations
NAND128-A, NAND256-A
6.3
Page program
The page program operation is the standard operation to program data to the memory array.
The main area of the memory array is programmed by page, however partial page
programming is allowed where any number of bytes (1 to 528) or words (1 to 264) can be
programmed.
The maximum number of consecutive partial page program operations allowed in the same
page is three. After exceeding this a Block Erase command must be issued before any
further program operations can take place in that page.
Before starting a page program operation a pointer operation can be performed to point to
the area to be programmed. Refer to Section 6.1: Pointer operations and Figure 9: Pointer
Each page program operation consists of the following five steps (see Figure 14: Page
1.
One bus cycle is required to setup the Page Program command
2.
Four bus cycles are then required to input the program address (refer to Table 6:
3.
The data is then input (up to 528 bytes/ 264 words) and loaded into the page buffer
4.
One bus cycle is required to issue the confirm command to start the P/E/R controller.
5.
The P/E/R controller then programs the data into the array.
Once the program operation has started the status register can be read using the Read
Status Register command. During program operations the status register only flags errors
for bits set to '1' that have not been successfully programmed to '0'.
During the program operation, only the Read Status Register and Reset commands are
accepted; all other commands are ignored.
Once the program operation has completed the P/E/R controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High.
The device remains in read status register mode until another valid command is written to
the command interface.
Figure 14.
Page program operation
1.
Before starting a page program operation a pointer operation can be performed. Refer to Section 6.1:
I/O
RB
Address Inputs
SR0
ai07566
Data Input
10h
70h
80h
Page Program
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH2
(Program Busy time)
相關PDF資料
PDF描述
NCP303LSN41T1 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5
NCS6416DWG 8-CHANNEL, VIDEO MULTIPLEXER, PDSO20
NCS6S4803L5C 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE
NCT050C-20.0000 CRYSTAL OSCILLATOR, CLOCK, 20 MHz, TTL OUTPUT
NCT250A-FREQ-OUT3 CRYSTAL OSCILLATOR, CLOCK, 4 MHz - 20 MHz, TTL OUTPUT
相關代理商/技術參數
參數描述
NAND32GAH0HZA5E 制造商:Micron Technology Inc 功能描述:NAND EMMC - Trays
NAND32GAH0HZA5F 制造商:Micron Technology Inc 功能描述:NAND EMMC - Tape and Reel
NAND32GAH0PZA5E 制造商:Micron Technology Inc 功能描述:EMMC 4.3 4GB 12X16 41NM - Trays
NAND32GAH0PZA5F 制造商:Micron Technology Inc 功能描述:NAND EMMC - Tape and Reel
NAND32GAHAKZO6E 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*