- 您現在的位置：買賣IC網 > PDF目錄359222 > MSC8144 (飛思卡爾半導體(中國)有限公司) Quad Core Digital Signal Processor PDF資料下載
參數資料
| 型號： | MSC8144 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 數字信號處理 |
| 英文描述： | Quad Core Digital Signal Processor |
| 中文描述： | 四核心數字信號處理器 |
| 文件頁數： | 50/80頁 |
| 文件大小： | 1146K |
| 代理商： | MSC8144 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
MSC8144 Quad Core Digital Signal Processor Data Sheet, Rev. 1
Electrical Characteristics
Freescale Semiconductor
50
2.7.5.9
Jitter Test Measurements
For the purpose of jitter measurement, the effects of a single-pole high pass filter with a 3 dB point at (baud frequency)/1667 is
applied to the jitter. The data pattern for jitter measurements is the Continuous Jitter Test Pattern (CJPAT) pattern defined in
Annex 48A of
IEEE
Std. 802.3ae. All lanes of the LP-Serial link shall be active in both the transmit and receive directions, and
opposite ends of the links shall use asynchronous clocks. Four lane implementations shall use CJPAT as defined in Annex 48A.
Single lane implementations shall use the CJPAT sequence specified in Annex 48A for transmission on lane 0. Jitter shall be
measured with AC coupling and at 0 V differential. Jitter measurement for the transmitter (or for calibration of a jitter tolerance
setup) shall be performed with a test procedure resulting in a BER curve such as that described in Annex 48B of
IEEE
Std.
802.3ae.
2.7.5.10
Transmit Jitter
Transmit jitter is measured at the driver output when terminated into a load of 100
Ω
resistive
±
5% differential to 2.5 GHz.
2.7.5.11
Jitter Tolerance
Jitter tolerance is measured at the receiver using a jitter tolerance test signal. This signal is obtained by first producing the sum
of deterministic and random jitter defined in
Section 2.7.5.9
and then adjusting the signal amplitude until the data eye contacts
the 6 points of the minimum eye opening of the receive template shown in
Figure 15
and
Table 37
. Note that for this to occur,
the test signal must have vertical waveform symmetry about the average value and have horizontal symmetry (including jitter)
about the mean zero crossing. Eye template measurement requirements are as defined above. Random jitter is calibrated using
a high pass filter with a low frequency corner at 20 MHz and a 20 dB/decade roll-off below this. The required sinusoidal jitter
specified in Section 8.6 is then added to the signal and the test load is replaced by the receiver being tested.
2.7.6
PCI Timing
This section describes the general AC timing parameters of the PCI bus.
Table 38
provides the PCI AC timing specifications.
Table 38. PCI AC Timing Specifications
Parameter
Symbol
33 MHz
66 MHz
Unit
Min
Max
Min
Max
Output delay
t
PCVAL
t
PCON
t
PCOFF
t
PCSU
t
PCH
t
PCRST-CLK
t
PCRST-OFF
t
PCRST
t
PCRHFA
2.0
11.0
1.0
6.0
ns
High-Z to Valid Output delay
2.0
—
1.0
—
ns
Valid to High-Z Output delay
—
28
—
14
ns
Input setup
7.0
—
3.0
—
ns
Input hold
0
—
0
—
ns
Reset active time after PCI_CLK_IN stable
100
—
100
—
μ
s
Reset active to output float delay
—
40
—
40
ns
Reset active time after power stable
1
—
1
—
ms
HRESET high to first Configuration Access
32M
—
32M
—
clocks
Notes:
1.
2.
See the timing measurement conditions in the
PCI 2.2 Local Bus Specifications
.
All PCI signals are measured from OV
DD
/2 of the rising edge of PCI_SYNC_IN to 0.4
×
OV
DD
of the signal in question for
3.3-V PCI signaling levels.
For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
Input timings are measured at the pin.
The reset assertion timing requirement for HRESET is in
Table 24
and
Figure 8
3.
4.
5.
相關PDF資料 |
PDF描述 |
|---|---|
| MSC82005 | RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS |
| MSC82010 | RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS |
| MSC82040 | RF & MICROWAVE TRANSISTORS GENERAL PURPOSE LINEAR APPLICATIONS |
| MSC82100 | RF & MICROWAVE TRANSISTORS GENERAL PURPOSE LINEAR APPLICATIONS |
| MSC82302 | RF & MICROWAVE TRANSISTORS GENERAL PURPOSE AMPLIFIER APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSC8144ADS | 功能描述:ADS FOR MSC8144 DEVICE RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| MSC8144AMC-SA | 制造商:Freescale Semiconductor 功能描述:BOARD AMC SGL WIDTH MSC8144 DSP |
| MSC8144E | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core Digital Signal Processor |
| MSC8144EC | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Quad Core Digital Signal Processor |
| MSC8144ESVT1000B | 制造商:Freescale Semiconductor 功能描述:DSP 32-BIT 1GHZ 1000MIPS 783-PIN FCBGA BOX - Trays 制造商:Freescale Semiconductor 功能描述:ENCRYPTION PACSUN R2.1 783FCPBGA |
發布緊急采購，3分鐘左右您將得到回復。