參數資料
型號: MQ80C52CXXX-36SCD
廠商: TEMIC SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CQFP44
文件頁數: 171/182頁
文件大?。?/td> 2994K
代理商: MQ80C52CXXX-36SCD
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁當前第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁
89
1477K–AVR–08/10
ATtiny26(L)
Figure 48. Two-wire Mode, Typical Timing Diagram
Referring to the timing diagram (Figure 48.), a bus transfer involves the following steps:
1. The a start condition is generated by the master by forcing the SDA low line while the
SCL line is high (A). SDA can be forced low either by writing a zero to bit 7 of the Shift
Register, or by setting the PORTB0 bit to zero. Note that DDRB0 must be set to one for
the output to be enabled. The slave device’s start detector logic (Figure 49.) detects the
start condition and sets the USISIF flag. The flag can generate an interrupt if necessary.
2. In addition, the start detector will hold the SCL line low after the master has forced an
negative edge on this line (B). This allows the slave to wake up from sleep or complete
its other tasks, before setting up the Shift Register to receive the address by clearing the
start condition flag and reset the counter.
3. The master set the first bit to be transferred and releases the SCL line (C). The slave
samples the data and shift it into the serial register at the positive edge of the SCL clock.
4. After eight bits are transferred containing slave address and data direction (read or
write), the slave counter overflows and the SCL line is forced low (D). If the slave is not
the one the master has addressed it releases the SCL line and waits for a new start
condition.
5. If the slave is addressed it holds the SDA line low during the acknowledgment cycle
before holding the SCL line low again (i.e., the Counter Register must be set to 14 before
releasing SCL at (D)). Depending of the R/W bit the master or slave enables its output. If
the bit is set, a master read operation is in progress (i.e., the slave drives the SDA line)
The slave can hold the SCL line low after the acknowledge (E).
6. Multiple bytes can now be transmitted, all in same direction, until a stop condition is given
by the master (F). Or a new start condition is given.
If the slave is not able to receive more data it does not acknowledge the data byte it has last
received. When the master does a read operation it must terminate the operation by force the
acknowledge bit low after the last byte transmitted.
Figure 49. Start Condition Detector, Logic Diagram
P
S
ADDRESS
1 - 7
8
9
R/W
ACK
1 - 8
9
DATA
ACK
1 - 8
9
DATA
SDA
SCL
A B
D
E
C
F
SDA
SCL
Write( USISIF)
CLOCK
HOLD
USISIF
DQ
CLR
DQ
CLR
相關PDF資料
PDF描述
IJ80C52XXX-16:R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44
IR80C52TXXX-L16R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44
IR80C52TXXX-16SHXXX:RD 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CQCC44
MR80C32-25/883R 8-BIT, 25 MHz, MICROCONTROLLER, CQCC44
MR80C52CXXX-12SBR 8-BIT, MROM, 12 MHz, MICROCONTROLLER, CQCC44
相關代理商/技術參數
參數描述
MQ82370-20 制造商:Rochester Electronics LLC 功能描述:- Bulk
MQ8238020 制造商:Intel 功能描述:CONTROLLER: OTHER
MQ82380-20 制造商:Rochester Electronics LLC 功能描述:- Bulk
MQ82380-20/R 制造商:Rochester Electronics LLC 功能描述:
MQ82592 制造商:Rochester Electronics LLC 功能描述:- Bulk