- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33989EG (飛思卡爾半導體(中國)有限公司) System Basis Chip with High-Speed CAN Transceiver PDF資料下載
參數資料
| 型號： | MCZ33989EG |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | CAN |
| 英文描述： | System Basis Chip with High-Speed CAN Transceiver |
| 中文描述： | 系統基礎芯片高高速CAN收發器 |
| 文件頁數： | 48/66頁 |
| 文件大?。?/td> | 1181K |
| 代理商： | MCZ33989EG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
48
33989
TYPICAL APPLICATIONS
SUPPLEMENTAL APPLICATION NOTES
CAN Mode versus SBC Modes
The table below indicates the CAN interface modes versus
the SBC modes as well as the status of TX, RX and the CAN
bus pins.
Table 34. CAN vs SBC Modes
How to Test the MC33989 CAN Interface
The CAN interface can be easily set up and tested.
MC33989 can be connected as in the following figure. V2 is
connected to V1. The device is supplied with nominal supply
(12 V at VSUP input pin). After power on, reset the device,
enter normal request mode, and the CAN interface is set in
normal mode, slew rate 0. TX can be driven by a signal
generator. RX will report the bus state. The figure below is a
simple test schematic.
Figure 38. Testing the CAN Interface
SBC mode
External
ballast
for V2
CAN mode
V2
voltage
TX
RX
CANH/CANL
(disconnected
from other
nodes)
Unpowered
YES
Unpowered
0 V
LOW
LOW
Floating to gnd
Reset (with ballast)
YES
0 V
LOW
LOW
Floating to gnd
Normal request (with ballast)
YES
0 V
LOW
LOW
Floating to gnd
Normal
YES
Normal Slew rate
0,1,2,3
5 V
Internal pull up
to V2.
Report bus state
High if bus
recessive, Low if
dominant
Bus recessive
CANH = CANL =
2.5 V
Normal
YES
Sleep mode
5 V
5 V
5 V
Floating to gnd
Standby with external ballast
YES
Normal or sleep
0 V
LOW
LOW
Floating to gnd
Standby without external
ballast, V2 connected to V1
NO
Normal
5 V
Same as
normal mode
Same as normal
mode
Same as normal
mode
Standby without external
ballast, V2 connected to V1
NO
Sleep
5 V
5 V
5 V
Floating to gnd
Sleep
—
Sleep
0 V
LOW
LOW
Floating to gnd
Stop
—
Sleep
0 V
LOW
LOW
Floating to gnd
V1
VSUP
V2CTRL
RESET
RST
INT
CS
MISO
MOSI
SCK
TX
RX
CANH
CANL
HS1
L0
L1
L3
C3
C4
C1
C2
RT
GND
CAN bus
WD
V2
L2
Signal generator
F<500kz (1Mb/s)
Components list:
C1: 22uF, C2: 100nF
C3: >10uF
C4: 100nF
Rt: 60 ohms
CANL
CANH
Signal at RX output
MC33989
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33990EF | Enhanced Class B Serial Transceiver |
| MCZ33991EG | Gauge Driver Integrated Circuit |
| MCZ33993EW | Multiple Switch Detection Interface |
| MCZ33996EK | 16-Output Switch with SPI Control |
| MCZ34652EF | 2.0 A Negative Voltage Hot Swap Controller with Enhanced Programmability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33989EG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
| MCZ33989EGR2 | 功能描述:網絡控制器與處理器 IC SBC-HS RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33990EF | 功能描述:網絡控制器與處理器 IC CLASS B SERIAL TRANS. RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| MCZ33990EF | 制造商:Freescale Semiconductor 功能描述:TRANCEIVER J-1850 CLASS B 8SOIC |
| MCZ33990EF/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Enhanced Class B Serial Transceiver |
發布緊急采購，3分鐘左右您將得到回復。