參數資料
型號： MC705C9ACPE
廠商： Freescale Semiconductor
文件頁數： 91/118頁
文件大小： 0K
描述： IC MCU 2.1MHZ 16K OTP 40-DIP
標準包裝： 9
系列： HC05
核心處理器： HC05
芯體尺寸： 8-位
速度： 2.1MHz
連通性： SCI，SPI
外圍設備： POR，WDT
輸入/輸出數： 24
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： OTP
RAM 容量： 352 x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 40-DIP（0.600"，15.24mm）
包裝： 管件
Serial Peripheral Interface (SPI)
MC68HC05C9A Advance Information Data Sheet, Rev. 4.1
74
Freescale Semiconductor
The SPI is double buffered on read, but not on write. If a write is performed during data transfer, the
transfer occurs uninterrupted, and the write will be unsuccessful. This condition will cause the write
collision (WCOL) status bit in the SPSR to be set. After a data byte is shifted, the SPIF flag of the SPSR
is set.
In the master mode, the SCK pin is an output. It idles high or low, depending on the CPOL bit in the SPCR,
until data is written to the shift register, at which point eight clocks are generated to shift the eight bits of
data and then SCK goes idle again.
In a slave mode, the slave select start logic receives a logic low at the SS pin and a clock at the SCK pin.
Thus, the slave is synchronized with the master. Data from the master is received serially at the MOSI
line and loads the 8-bit shift register. After the 8-bit shift register is loaded, its data is parallel transferred
to the read buffer. During a write cycle, data is written into the shift register, then the slave waits for a clock
train from the master to shift the data out on the slave’s MISO line.
Figure 10-3 illustrates the MOSI, MISO, SCK, and SS master-slave interconnections.
Figure 10-3. Serial Peripheral Interface Master-Slave Interconnection
10.5 SPI Registers
Three registers in the SPI provide control, status, and data storage functions. These registers are called
the serial peripheral control register (SPCR), serial peripheral status register (SPSR), and serial
peripheral data I/O register (SPDR) and are described in the following paragraphs.
10.5.1 Serial Peripheral Control Register
The SPI control register (SPCR), shown in Figure 10-4, controls these functions:
Enables SPI interrupts
Enables the SPI system
Selects between standard CMOS or open drain outputs for port D (C9A mode only)
Selects between master mode and slave mode
Controls the clock/data relationship between master and slave
Determines the idle level of the clock pin
SPI SHIFT REGISTER
7 6 5 4 3 2 1 0
SPI SHIFT REGISTER
7 6 5 4 3 2 1 0
SPDR ($000C)
PD3/MOSI
PD2/MISO
PD5/SS
PD4/SCK
MASTER MCU
SLAVE MCU
I/O PORT
相關PDF資料
PDF描述
2-6457567-2 ADPTR,DUP,LC,SR BLU,CER,LOGO
V24A28T400BF3 CONVERTER MOD DC/DC 28V 400W
V24A28T400BF2 CONVERTER MOD DC/DC 28V 400W
V24A24T400BG3 CONVERTER MOD DC/DC 24V 400W
V24A24T400BG2 CONVERTER MOD DC/DC 24V 400W
相關代理商/技術參數
參數描述
MC705E6CDWE 制造商:Freescale Semiconductor 功能描述:
MC705J1A 制造商:Freescale Semiconductor 功能描述:
MC705J1ACDWE 功能描述:8位微控制器 -MCU HCO5 CORE+1.2K RAM + EPR RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC705J1ACDWE 制造商:Freescale Semiconductor 功能描述:8-Bit Microcontroller IC
MC705JJ7CDWE 功能描述:8位微控制器 -MCU 705JJ7 224 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*