- 您現在的位置：買賣IC網 > PDF目錄45217 > MC68HC705BD7B (MOTOROLA INC) 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP42 PDF資料下載
參數資料
| 型號： | MC68HC705BD7B |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP42 |
| 封裝： | SDIP-42 |
| 文件頁數： | 27/85頁 |
| 文件大?。?/td> | 302K |
| 代理商： | MC68HC705BD7B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
SECTION 4: INTERRUPTS
MOTOROLA
Page 23
MC68HC05BD7 Rev. 2.0
GENERAL RELEASE SPECIFICATION
PRELIMINARY
4.2
Reset Interrupt Sequence
The RESET function is not in the strictest sense an interrupt; however, it is acted upon in a
similar manner. A low level input on the RESET pin or an internally generated reset signal
causes the program to vector to its starting address which is specified by the contents of
$3FFE and $3FFF. The I-bit in the condition code register is also set. The MCU is
configured to a known state during this type of reset as described in SECTION 5.
4.3
Software Interrupt (SWI)
The SWI is an executable instruction and a non-maskable interrupt since it is executed
regardless of the state of the I-bit in the CCR. If the I-bit is zero (interrupts enabled), the
SWI instruction executes after interrupts which were pending before the SWI was fetched,
or before interrupts generated after the SWI was fetched. The interrupt service routine
address is specified by the contents of $3FFC and $3FFD.
4.4
Hardware Interrupts
All hardware interrupts except RESET are maskable by the I-bit in the CCR. If the I-bit is
set, all hardware interrupts (internal and external) are disabled. Clearing the I-bit enables
the hardware interrupts. There are four types of hardware interrupts which are explained in
the following sections.
4.4.1
External Interrupt (IRQ)
If the IRQ option is edge and level sensitive triggering (IRQN=0), a low level at the IRQ pin
and a cleared interrupt mask bit of the condition code register will cause an EXTERNAL
INTERRUPT to occur. If the MCU has finished with the interrupt service routine, but the IRQ
pin is still low, the EXTERNAL INTERRUPT will start again. In fact, the MCU will keep on
servicing the EXTERNAL INTERRUPT as long as the IRQ pin is low. If the IRQ pin goes
low for a while and resumes to high (a negative pulse) before the interrupt mask bit is
cleared, the MCU will not recognize there was an interrupt request, and no interrupt will
occur after the interrupt mask bit is cleared.
If the IRQ option is negative edge sensitive triggering (IRQN=1), a negative edge occurs at
the IRQ pin and a cleared interrupt mask bit of the condition code register will cause an
EXTERNAL INTERRUPT to occur. If the MCU has finished with the interrupt service
routine, but the IRQ pin has not returned back to high, no further interrupt will be generated.
The interrupt logic recognizes negative edge transitions and pulses (special case of
negative edges) only. If the negative edge occurs while the interrupt mask bit is set, the
interrupt signal will be latched, and interrupt will occur as soon as the interrupt mask bit is
cleared. The latch will be cleared by RESET or cleared automatically during fetch of the
EXTERNAL INTERRUPT vectors. Therefore, one (and only one) external interrupt edge
could be latched while the interrupt mask bit is set. If the INHIRQ bit in the MFT register is
set, no IRQ interrupt can be generated.
The service routine address is specified by the contents of $3FFA and $3FFB. Figure 4-2
shows the two methods for the interrupt line (IRQ) to be recognized by the processor. The
first method is single pulses on the interrupt line spaced far apart enough to be serviced.
The minimum time between pulses is a function of the number of cycles required to execute
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05C0B | 8-BIT, 4 MHz, MICROCONTROLLER, PDIP42 |
| MC68HC05C0P | 8-BIT, 4 MHz, MICROCONTROLLER, PDIP40 |
| MC68HC05C0FN | 8-BIT, 4 MHz, MICROCONTROLLER, PQCC44 |
| MC68HC05C12AFN | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQCC44 |
| MC68HSC05C12AB | 8-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PDIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC705BD7P1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC68HC705C4ACP | 制造商:Freescale Semiconductor 功能描述: |
| MC68HC705C8AB | 功能描述:IC MCU 8K OTP 2.1MHZ 42-SDIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC705C8ACB | 制造商:Rochester Electronics LLC 功能描述:HCO5 CORE + 8K RAM + EPR - Bulk |
| MC68HC705C8ACFB | 功能描述:IC MCU 8K 4MHZ OTP 44-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC05 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
發布緊急采購，3分鐘左右您將得到回復。