- 您現在的位置：買賣IC網 > PDF目錄2011 > MAX5898EGK+D (Maxim Integrated Products)IC DAC 16BIT DUAL 500MSPS 68-QFN PDF資料下載
參數資料
| 型號： | MAX5898EGK+D |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 18/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT DUAL 500MSPS 68-QFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 30 |
| 設置時間： | 11ns |
| 位數： | 16 |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 831mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 68-QFN 裸露焊盤（10x10） |
| 包裝： | 管件 |
| 輸出數目和類型： | 2 電流，單極 |
| 采樣率（每秒）： | 500M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
MAX5898
16-Bit, 500Msps, Interpolating and Modulating
Dual DAC with Interleaved LVDS Inputs
______________________________________________________________________________________
25
Power-Down Mode
The MAX5898 features three power-saving modes.
Each DAC can be individually powered down through
bits 2 and 3 of address 00h. The interpolation filters can
also be powered down through bit 4 of address 00h,
preserving the output level of each DAC (the DACs
remain powered). Powering down both DACs automati-
cally puts the MAX5898 into full power-down, including
the interpolation filters.
Applications Information
Frequency Planning
System designers need to take the DAC into account
during frequency-planning for high-performance appli-
cations. Proper frequency planning can ensure that
optimal system performance is achieved. The
MAX5898 is designed to deliver excellent dynamic per-
formance across wide bandwidths, as required for
communication systems. As with all DACs, some com-
binations of output frequency and update rate produce
better performance than others.
Harmonics are often folded down into the band of inter-
est. Specifically, if the DAC outputs a frequency close
to fS / N, the Mth harmonic of the output signal will be
aliased down to:
Thus, if N
≈ (M + 1), the Mth harmonic will be close to
the output frequency. SFDR performance of a current-
steering DAC is often dominated by 3rd-order harmonic
distortion. If this is a concern, placing the output signal
at a frequency other than fS / 4 should be considered.
Common to interpolating DACs are images near the
divided clocks. In a DAC configured for 4x interpolation,
this applies to images around fS / 4 and fS / 2. In a DAC
configured for 8x interpolation, this applies to images
around fS / 8, fS / 4, and fS / 2. Most of these images
are not part of the in-band (0 to fDATA / 2) SFDR specifi-
cation, though they are a consideration for out-of-band
(fDATA / 2 to fDAC / 2) SFDR and may depend on the
relationship of the DATACLK to DAC update clock (see
the
Data Clock section). When specifying the output
reconstruction filter for other than baseband signals,
these images should not be ignored.
Data Clock
The MAX5898 features synchronizers that allow for arbi-
trary phase alignment between DATACLK and
CLKP/CLKN. The DATACLK causes internal switching in
the MAX5898 and the phase between DATACLK (input
mode) to CLKP/CLKN influences the images at DATACLK.
Figure 14 shows the image level near DATACLK as a
function of the DATACLK (input mode) to CLKP/CLKN
phase at 500Msps, 4x interpolation for a 10MHz, -6dBFS
output signal.
Clock Interface
The MAX5898 features a flexible differential clock input
(CLKP, CLKN) with a separate supply (AVCLK) to
achieve optimum jitter performance. Use an ultra-low
jitter clock to achieve the required noise density. Clock
jitter must be less than 0.5psRMS to meet the specified
noise density. For that reason, the CLKP/CLKN input
source must be designed carefully. The differential
clock (CLKN and CLKP) input can be driven from a sin-
gle-ended or a differential clock source. Differential
clock drive is required to achieve the best dynamic
performance from the DAC. For single-ended opera-
tion, drive CLKP with a low noise source and bypass
CLKN to GND with a 0.1F capacitor.
The CLKP and CLKN pins are internally biased to
AVCLK / 2. This allows the user to AC-couple clock
ff
M f
f
NM
N
S
OUT
S
=×
=
Figure 14. Effect of CLKP/CLKN to DATACLK Phase on fS / 4
Images
fS / 4 IMAGES vs. CLKP/CLKN to DATACLK DELAY
fDATA = 125Mwps, 4x INTERPOLATION
CLKP/CLKN DELAY (s)
IMAGE
LEVEL
(dBc)
6
4
2
-95
-90
-85
-80
-75
-70
-100
08
fOUT = 10MHz
AOUT = -6dBFS
fS / 4 + fOUT
fS / 4 - fOUT
fS / 4 + fOUT
fS / 4 - fOUT
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6900ETT+T | IC RTC I2C COMPAT 6-TDFN |
| MAX6902ETA+T | IC RTC SPI COMPAT 8-TDFN |
| MAX7375AXR604+T | IC OSC SILICON SC70-3 |
| MAX7394ATTLY+T | IC OSC SILICON 922KHZ 6-TDFN |
| MAX7403CSA+ | IC FILTER LOWPASS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5898EGK-TD | 功能描述:數模轉換器- DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5898EVCMOD2 | 功能描述:數模轉換器- DAC Evaluation System/Evaluation Kit for the MAX5898 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5898EVKIT | 功能描述:數模轉換器- DAC Evaluation System/Evaluation Kit for the MAX5898 RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| MAX5900AAETT | 制造商:Maxim Integrated Products 功能描述:SIMPLE SWAPPER HOT-SWAP CONTROLLER - Rail/Tube |
| MAX5900AAETT+ | 制造商:Maxim Integrated Products 功能描述:SIMPLE SWAPPER HOT-SWAP CONTROLLER - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。